Brand: KitchenAid

I have a Kitchen Aid wall oven, electric heat. Model # KEBS107DAL4 – gives fault code:
F3 – E2 ( Oven too hot Replace oven temperature sensor)
This fault code only when self-cleaning. Bake and Broil works fine.
Wouldn’t the sensor fail for baking as well? Thanks in advance for any help.

I had posted on this dishwasher yesterday. I went back this AM to double check it.
This is a solid door unit (stainless) no vent assy on this door or in the front.
It does have 3 small vent slits on the top left side of the console, it looks like for a vent but no flap assy in the door. I had the unit out on the floor with the front off. The metal bracket in the console has cut out as for mounting of a vent assy. but nothing there. I’m not finding anything on a vent issue.
What am I missing on this one?

My Kitchenaid dishwasher will not start.

Have an odd one here. display on touch pad goes dead after a few weeks. unplug unit and it restores normal operation, been out 2 times and unplugged and came back on. I don’t want to just throw parts at this, anyone see this before or have any suggestions. Thanks in advance

The dispenser door on my Kitchenaid dishewasher will not close.

My Kitchenaid oven will not heat on the bake setting.

Upper oven after preheating and after 5 min after is done pre heating a gas smell comes out and the igniter is lit but the burner doesn’t seem to be on. Please help

I’ve tested the heating element and thermostat. Both test ok. Not sure what else to try besides replacing the control board.

Keeps shutting off.

Surface burner will not turn off.

I’ve had a job numerous times And they keep referring them to Warrantee because I’m assuming if the fuel system issue but I followed up with several of these customers and they said warranty he came out and fixed it in like 10-15 minutes. I have the job again and I’m wondering what the guys from warranty did there must be a service bulletin out for this basically build up a snow blocks only underneath where the fan is located on the evaporator you guys answer this question before that it might be deprived evaporator But how could they be fixed in 10 to 15 minutes? Please don’t link videos or diagnostic stuff unless it addresses this exact issue with this freezer fan.

Does anyone have a tech sheet for a KitchenAid refrigerator model number KSCS23FVBL01.

Oven was working fine and then we noted that it was in “Preheat” mode with the temperature decreasing. Tried the following, turned off and tried bake then broil, then convection – nothing changed. Opened supply breaker and reclosed. Same “preheat”. Any suggestions before we call the repair service?

5 DOOR REFRIGERATOR HERE AND IS GIVING PO CODE. THE MAIN BOARD AND THE POWER CONTROL BOARD BOTH HAVE BEEN CHANGED. THE COMPRESSOR CYCLES OF AND ON ABOUT EVERY 30 SECONDS TO A MINUTE. THERE IS FROST BUILD UP IN THE MIDDLE SECTION AND SOME IN THE FREEZER SECTION. ALL WIRES IN THE LEFT DOOR HAVE BEEN SPLICED. SOMEONE TOOK THE TECH SHEET, SO I CANNOT GET INTO DIAGNOSTIC MODE. ANY HELP ON THIS ONE WOULD BE WONDERFUL.

The dishes in my dishwasher are coming out dripping wet.

My Kitchen aid refrigerator is not making ice.

I am working on a 4 door kitchenaid refrigerator that has icemaker in the celling in refrigerator side how do you get it out , dose anybody have a service manual to share whit me MOD#KFIS29PBMS02 and SER#K33307442 help is very appreciated

I CLEANED THE COILS TO THE BEST OF MY ABILITIES, BUT THEY WERE HARD TO GET TO. I MANUALY OPENED THE AIR DIFFUSER, AND CHECKED THE EVAP. THE EVAP HAD A CONCENTRATION OF ICE BUILD UP IN ONE AREA, BUT EVEN IN ALL OTHER AREAS. THE FANS ARE BOTH RUNNING FINE AS WELL AS THE COMPRESSOR. WHEN I LEFT I COULD ONLY GET THE FRIDGE TO 48 AND THE FREEZER TO 20, BUT THE UNIT WAS EMPTY AND ROOM TEMP WAS ABOUT 80. YOUR THOUGHTS? THANKS, TODD FROM NY.

Hi Folks,
This dryer was in a very poor condition. The pulley had fallen off the fan and the owner kept using it with no circulation of heat. No fuses were found to be defective. Element checks out! Proceeded to clean the unit thoroughly. Took care of the pulley and circulation problems. Put it all back together and no heat. Check the board and it was fried. Installed a new board and still no heat. There was no tech sheet with the unit! Now I have 240v going to the board (two legs of 120v each) but where do I find the legs coming out. It’s the heating cycle because the dryer is turning but no heat. I need a tech sheet and some expertise on getting this unit on board!
Thank you,

Jan
Barney’s Appliance

Hello. I have been bombarded with fridge calls, and I dislike most “modern ” fridges. My customer has a KitchenAid fridge. The fridge works, but the display panel is out. Not lit up. She has no control of the temperatures. I did some internet research and believe that the display board is bad. Is there a way to determine so? Why is it when it comes to any board, I feel helpless? Is it a guessing game when it comes to determining gourds? Other than burn marks that are obvious.
Thanks Bob

My Kitchenaid stove is not working properly.

My Kitchenaid oven is not heating properly.

Ordered both tension rods. Installed new ones door still falls.

I’ve tested the heating element and thermostat. Both test ok. Not sure what else to try besides replacing the control board.