Brand: Maytag

dryer noise is getting louder, and high pitched, how can I fix this?

My washing machine when the timer goes to spin,it won’t spin,instead the agitator spin clockwise and anti clockwise like in wash mode while draining the water. When I took my clothes out after spin cycle is over,still water on it.What is the problem of my spin cycle?Thank you very much

Sincerly,

Loremer

This washer gets to spin cycle and won’t drain. You can hear hum and burning smell. Most of the time I can rock the machine front to back or visa versa and it will start to drain and spin. The occurrences of this are getting more frequent and it is getting harding to get the machine to start back up by rocking it. Sometimes now have to unplug it for awhile and try. Also it seems easier to get to work if I take clothes out of machine.

My gas dryer isn’t heating up any longer and everywhere I looked suggested the coils. But when I accessed them and checked them, there weren’t any issues. What should I move on to next? Thermostat?

I have a Maytag refrigerator with a bottom freezer. The upper unit doesn’t cool. I found a video that shows how to replace the jazz-board which I did. This did not fix the problem. I can hear the lower unit (compressor) running and the freezer works fine. Maytag model number MFF2557HEW.

GETTING POWER INTO THE BOARD, LIGHTS WORK & CHECKED FUSE; TESTED GOOD BUT CAN NOT GET DISPLAY TO POWER UP. ORIGINAL ERROR CODE WAS F16.

Hello, I am in need of a reverse solenoid part #900414 for my Maytag WU701 dishwasher; it’s from 1982 and the exterior is in pristine condition and everything else works like a charm…except the part mentioned.

The part is no longer available and extensive google searches have come up empty. So, I thought I’d try to repair the part myself. It is a reverse solenoid to open the detergent door. Wondering if you might have any suggestions for me?

Thanks so much.
Monica

My Maytag washer will not agitate. It fills, drains, and spins fine. When it comes to the agitate part of the cycle, it makes a low humming noise ( I believe this is the same noise as it normally makes, only minus the sounds of swishing water). After a while, a squealing noise starts, and I can smell burning rubber. The noise is just like a loose belt in a car. The loss of agitation was also progressive, from a ‘weak’ wash, to very minimal movement of the agitator, to complete failure to move, along with the other symptoms.

I checked the belts and they are fine, and there is no oil or liquid leaking. With the belt off, the large central pulley underneath is hard to turn counter-clockwise, and moderately hard to turn clockwise. There is no grinding, rumbling, or clinking noises. The tensioner moves freely.

I might guess that perhaps the transmission has become clogged or the grease has become sticky, or something has wound itself around the parts somewhere?

*This is an edited repeat of an earlier question, but with more details.

Any help is appreciated.

DOES NOT agitate
Makes low humming noise
Eventually starts making squealing noise like a loose car fan belt
Eventually burning rubber smell appears
DOES spin
DOES drain/fill water

Thanks.

[edit] The belts look ok, although the one to the big pulley seems loose? I can rotate the big central pulley about half a rotation either way before the pulley ‘catches’, and then the belt starts to slide.

I know there is good pressure and there is only one water line that comes out of the water solenoid in the back of my fridge. my assumption is that it goes to the filter first then splits to the water dispenser and ice maker. so my question is why is my ice maker not getting water? is there a sensor on the ice maker itself that tells the ice maker to draw water. also I put some water in the tray to see if it would make cubes and it did not. what do you think I need to replace. thanks.

replaced control oard with reman unit cannot program new unit

I believe my icemaker failed leaving it run for a while (bad thermostat?)

The upper part of the freezer was wet and warm, and the compressor is not running. I power cycled the refrig, and it is still not starting up…but taking about .3 amp of power at 125VAC.

This unit has an ADC in it, but I know the “test” feature does not work on the replacement ADC which is in it.

What should I be going after?

the refrigerator started flashing the digital temperature lights not responding to water or ice controls. intermittently. gradual ly worsened and stopped cooling refrigerator and freezer. is this a motherboard failure? if so how much is the part, and availability?

My dryer seems to heat perfectly fine sometimes, and then other times it takes almost double the time to dry. From what I’ve read on here, it seems like gas coils are the likely answer? Wanted to check before ordering any parts.

Our dishwasher lights up, has power, but will not start. Sometimes if I cancel it, open and close the door, and hit start again, it begins. But it’s getting more and more frustrating. Any thoughts on what it could be?

I have a maytag microwave and a few months ago the fan would make a lot of noise while it was on high. The noise sounded as if the blades were hitting against something. Not long after the microwave started making that noise during heating as well. Last week, the microwave made a loud noise while heating and the noise stopped all together and it sounded like the problem went away. Well today I used the microwave and it didn’t really sound like a microwave should. There really was no “normal” noise. I could only hear the tray spinning and not the regular microwave hum. Can this microwave be fixed or does it need to be replaced?

Thank you in advance for your help.

Not sure if this is a cycling problem or a bad timer? Dishes are clean(but slimmy not rinsed) and standing water is not dirty but sometimes cloudy.

brian,,
I removed icemaker from refrig., took plastic cover off nose. There is a sort of “L” shaped black plastic piece attached by a screw, about 1inch vertical, 1 and 3/4 inch horizonal, covering the T and H holes on the endpiece. It has a yellow wire into it, and a short metal probe that fits into the H hole. To run the diagnostic with a jumper wire, I would have to leave the L-shaped piece unattached, reinstall the icemaker, reattach the wiring harness. Then should I turn the icemaker switch to the on position and then use the jumper wire to see if the icemaker cycles? Am I going to short out or burn something out doing this? I am hesitant to do this. What do you suggest?
Thanks, ron again

You sent me instructions to use key pad to enter into diagnostic mode. That doesn’t work. It will not respond into that mode using the keypad steps as instructed. What would you do next if you were me? thanks

the 1st steps just yield c– – f on the freezer display and 0c on refrig display when I do steps 1,2,3. it reverts back to set freezer temp and refrig temp after a few minutes. what am I doing wrong?

It made 1-2 trays , maybe smaller, after being turned on after vacation. No more. Took icemaker out (thanks to your video).
There were 2or 3 of the back receptacles in the mold that had a little ice in them. I cleaned them out, reinstalled icemaker.
I also replaced the water supply line with a new one and hooked it to a direct water inlet valve so that it would have plenty of water pressure. Didn’t help. Still no water being supplied into mold. Supply tube into mold not iced up. Any ideas? This refrigerator is 1yr. 9mos. old

My fridge stopped working after our neutral line in the house was severed blowing most appliances not on protectors. I replaced the control board hoping it would fix it like my stove but not so.
Reprogramed to code 12 and the board is working correctly fan comes on but make a chugging sound (did that when it worked right) but no compressor. I looked at the wiring diagram and see a relay for the compressor, could this be it or is there another fuse or issue I may have. How do I trouble shoot this from here? Or is my fridge beyond repair?

I have the above Model refrigerator freezer and have been experiencing the ice up problem. I would like to know if the P-Trap kit is available for my model. If so, is it your opinion that this would solve the problem, and what is the cost of the kit?
Thanks!
Les Hooker

How can I winterize my dishwasher for my summer cottage. I drain all the water from the system and use the air compressor to finalize so no water is in the lines. RV antifreeze to the traps.
Can you assist? I saw many of your you tube videos for how tos but not on the dishwasher winterization
Thanks

The bottom freezer compartment has been accumulating ice on compartment floor. Water frequently pools on the kitchen floor. After watching your video, I removed the back panel and inspected the duck bill foot valve (grommet). It was dry. No accumulated gunk inside. The drain pan designed to catch drain water from the drain tube w/ grommet was also dry. Did not look like water had been there for a long time if ever. The refrigerator is just over three years old. This problem has been with us for at least a year. It appears there is a stoppage in the drain tube above the grommet. Any suggestions?
Thank you
Tom Nelson

Thanks for the great video on fixing the leaking water in the may tag refrigerator. Prior to seeing your video I removed the rear panel looking for a blockage in the drain. I removed the black nipple and found a small white rubber piece inside. I’ve removed it but was wondering if I should put it back? Thanks again for the video!

Cory

I have a maytag side by side fridge with ice maker and water dispenser in the door that worked perfect. Until I removed the doors to transport it to another location. When I placed the doors back on I have no water or ice dispenser. it still makes ice. there is power going to the door panel because the lights are on. When you push the button for ice nothing happens the auger motor does not turn or the trap door for the ice does not open. the same when you push the button for the water nothing happens. I check for power going to the switch. I have power at the switch and the power goes to the mother board but does not go any father then that. is it possiable that the board burnt out just like that. any help you can give me would be appricated thank you