Brand: Whirlpool

How do I access all the components to fix magnetron diode fan capacitor and HV CAPACITOR.

I have a dryer the as soon as you hit start you get an E02, f06 error code any thoughts?

the touch pad display went blank on our 10 year old oven during the night. Time does not show. No touchpad selections work except to turn on the oven light. Every few hours the oven will beep several times on it’s own. Only once however, did the error codes appear. When we try to use the various touchpad features, we get either one or several beeps, but nothing shows on the touchpad screen. I turned off the circuit breaker for 10 minutes and then turned it back on; no change. What do the error codes mean, and how can this matter be fixed?

Eastoriver

How do you put into forced defrost mode and which board (ui assy in fresh food section, or electronic control near compressor) controls defrost? (mini service manual missing)

Washer will not complete delicate cycle just continues to run and run and run customer has stopped it manually and spin it out on rinse and spin.

Sir, my front load washer water , I start the cycle door locked with red light ,then water filled a splash stop. Door unlocked and locked again with no water filling and the door light on again After that wait 1 minute with error code f28. Please.advice thank

The gas duet dryer only lights up for touch up mode and 15 minutes. When I turn knob for different settings touch up still stays lit. Automatic controls will not work no matter were control knob is turned. I can adjust settings on right side including time and heat but everything else does nothing. The original complaint was a F01 code.

Error f6e1 and f3e2 I replaced ccu did not fix wires are fine do you think it is the ui or mcu

This unit has a hidden bake element. I’m wondering how to remove it. It doesn’t have any screws on the inside to remove the bottom panel to get to it.

I have a washer whirlpool
Customer states code light on unit fill and done light and lock light flashing , Also stated that unit not in use made a locking sound them looked found unit lock light flashing again Building engineer already replaced the lock switch everything test good in your manual mode Do we have any ideas

Ice maker doen’t work?

I have a Whirlpool French Door Bottom Mount Refrigerator. The icemaker has a slow drip out of the front of the icemaker heater cover. The water slowly drips down into the front ice bin. the Ice bin in the front door builds up with ice and eventually the water starts to run out of the opening of the front door and the water and Ice dispenser unit installed on the front door.

How do I stop the water from dripping out of the icemaker front cover?

The element is not grounded. The relay is not welded closed.

My Whirlpool washer is displaying an error code

Hi Folks,
This unit contains a W10135090 Board which is replaced by a part number 2252189 but this replacement board is hard to come by. They just don’t have them in stock! Why I don’t know! The Repair Shack made a repair on the W10135090 and said it was good to go…Installed and still not cooling. But in the fresh food compartment controls if you install a bulb in to the top of socket near the Led the Led goes off. If you loosen the bulb the LED showing the temperature setting goes back on! Anyone have any ideas on this situation. All input greatly appreciated.

Everything works except there is NO agitation during wash or rinse cycle. Washes, drains and spins fine

Whirlpool Refrigerator French door bottom freezer. The unit is all iced up where the Ice maker is? How to you take the Ice maker out? It has all snap parts with screws to come out.

it runs through normal cycle good but when I put it on casual, delicate, or hand washables cycle it will do everything but spin after its done draining

How do you know what valve is causing a water problem? Water is all inside where the ice maker is at. There is a primary valve which they call a smart valve. Then there’s a secoundary valve.

Ice forming around ice maker looking at this model GI7FVCXWY62 not sure why there is Ice forming. This Refrigerator is real problem. You say there is a facial heater for the unit. They say there is only a mold heater, when I talked to Whirlpool. They also said they are not having any issues with the unit. There are problems and I don’t know what is real causing the iceing problem. Does the unit have factory problem thats causing this iceing problem. Please let me know I so confused about the whole thing. I just don’t understand why they ever put the ice maker in the upper left side of the refrigerator. I really think it is a bad design. The plastic that you have to pull down is so brittle and you can break a part so easy. All the cold tempatures for years and years of operation. Please let me know if this model of refrigerator does have a fix for ice problem.

Thank You
Dale

the small belt for the blower motor keeps falling off.
I didn’t not see anything that I can adjust

Drains in drain and spin, but will not drain in the regular cycle. We have already changed the actuator.

Won’t start beeps when it the start button. Customer says error code once F70 interface board doesn’t light up either. F70 says if the drum isn’t Turing to replace the CCU.

REPLACED CONTROL PANEL ONLY HAVE 10.6 VOLTS TO CUBE SOLENOID NO WIRING DIAGRAM WHAT SHOULD I LOOK FOR ? THIS IS A ESTATE SIDE BY SIDE MADE BY WHIRLPOOL

RAN DIAGNOSTICS STARTED FILLING WENT ALL THE WAY TO C6 THEN WOULDN’T CONTINUE. I CANCELLED THE DIAGNOSTICS . ALSO WHEN DIVERTER VALVE IS ON HIGH PITCH NOISE WHEN I PULL THE WIRE IT STOPS IS THAT AN INDICATION THAT THE VALVE IS BAD.