All Answers

Hello
See the complete diagnostic link below. Run through diagnostics to determine your issue. I have also provided video links to similar model dishwasher. Matt Ace technician

Hello
I did not see any service bulletins on this model. This sounds like a defrost issue , I recommend running it throgh the diagnostics. See technician link below it starts diagnostics on page #22 . I have also provided a similar model with video links below. Matt Ace technician

Hi. Your drain motor may be faulty. On the tech sheet that I have attached for you, it shows the drain pump should have 15-19 ohms. So if you’re only getting around 3-4 it needs to be replaced. Some of these units were known for taking out the control board when the drain pump would burn up, so be causes with this and be ready to install a control board as well. You can test to see if you board is still good by checking for 120 v being sent to the pump when in drain mode. You can do this at the board at pins p11-4 and p11-6. brown wires. Or at p11-4 – p12-6.

Hi. The number of coils on the surface burners will not create a electrical issue or any safety issues. As long at the replacement coils has the same wattage rating as the old one you will not have any trouble.

HI. I have found the service manual on this unit for you.

Hi. I have attached a link to the wiring diagrams for this unit. They are the last 2 parts diagrams on the page.

Hi. It does not look like there is a service manual for this unit. I found the tech sheet and have attached it for you. If the compressor and fans are all running and the unit is not cooling you more than likely have a sealed system issue. A leak in the refrigerant system or a faulty compressor. How is your frost pattern on the evaporator?

Hi. During preheat you will hear the relays clicking a lot. This is normal. Most ovens now use both broil and bake elements during preheat to get to temp. quicker. Then throughout the rest of a bake cycle they will only use the bake element to cycle on and off as needed to maintain temps. What was the initial issue? Is it now heating and working properly? As long as the unit is working and heating properly to correct temps, I would not worry about the clicking. This is normal.

Hello
There is not an exact service bulletin for this model on freezing water lines. There is one for Excessive interior moisture that I have linked below. We have seen this happen on units that the water dispenser does not get used for several days or more. We advise customers that run into this issue to use the dispenser for 30 seconds every other day. This has corrected their issue. On some Whirlpool models there is an add on insulation kit, this model is not on the list. Matt Ace technician

Hello

The Frigidaire refrigerator showing SY CE . When your Frigidaire refrigerator displays the SY CE error code, this means there is a communications issue. This communication problem is caused by either a wiring issue, wire harness issue, faulty control board, or a bad user interface board. Below we will show how to troubleshoot the SY CE error code on a Frigidaire refrigerator. NOTE: The Frigidaire error code SY CE may look or be determined to be 5Y CE.Try and clear the SY CE error code the easiest way, try unplugging your Frigidaire Refrigerator for 15 minutes. After 15 minutes plug the refrigerator back in. This may have reset the control board and cleared the error code. If not, see below…
How to diagnose and clear the SY CE error code (Remove power to the refrigerator before troubleshooting)

MAIN CONTROL BOARD – LOCATED UNDER THE REFRIGERATOR BEHIND KICK PANEL
* Check the wires/wiring on the main control board.
* Check to be sure wires/wiring is secure on the board and not damaged.
* Visually check the main control board for signs of burns/melted areas.
*Disconnect all wires on main control board and plug back in.

USER INTERFACE DISPLAY BOARD/PANEL – LOCATED BEHIND DISPLAY PANEL
* Check the wires/wiring on the user interface display panel/board.
* Check to be sure wires/wiring is secure on the interface and not damaged.
* Visually check the user interface board for signs of burns/melted areas.
* Disconnect all wires on user interface display panel/board and plug back in.

Hello
See video link with Samsung model ice maker you have damaged refrigerant line. The upper line looks like a heater but really is a refrigerant line. There is no replacement for this refrigerant line as it is foamed into the back of the unit. You can repair the line by evacuating the system into a slight vacuum and putting on the aluminum heat stick repair and epoxy kit over the heat stick. We have repaired two so far from other companies making the same mistake. This is very easy to confuse if you have never seen it. Matt Ace technician

Hello
We have run into this situation many times and it sounds like you have a defective diode assembly. Here is the part number for harness and diode. W10402006 Harness

PROBLEM: Bake Temperature Needs- See complete diagnostic link below .
Adjustment
1. Press BAKE pad for 5 seconds. The default temp. 0°
or a previously entered offset temperature will show
in the Temperature Display.
■ Press the TEMP pad “up” arrow ( ) to increase
the temperature in 10° F or 5° C increments.
■ Press the TEMP pad “down” arrow ( ) to decrease
the temperature in 10° F or 5° C increments.
Maximum offset temperature adjustment is ±30° F or
±15° C.
2. Press the START pad to save the temp. adjustment.

Before servicing, perform the following checks:
The most common cause for control failure is corrosion
on connectors. Therefore, disconnecting and
reconnecting wires will be necessary throughout test
procedures.
All tests/checks should be made with a VOM or DVM
having a sensitivity of 20,000 ohms per volt DC or
greater.
Check all connections before replacing components,
looking for broken or loose wires, failed
terminals, or wires not pressed into connectors
far enough.
Voltage checks must be made with all connectors
attached to the boards.
Resistance checks must be made with power cord
unplugged from outlet, and with wiring harness or connectors disconnected .

Hello
See technician diagnostic sheet below. Hello you should have 12vdc between terminals J4A-7 and J4B-5 . See complete manual below. Matt Ace technician

Hello
See the technician information links below along with the service bulletins. Are you getting power to the ice maker and the auger motor ? Run the unit throgh the diagnostics mode. See links below. Matt Ace technician
Entering Service Diagnostics
Enter Service mode by pressing the “Water”, “Crushed”, and “Cubed” buttons simultaneously for 3 seconds.
The display will show 00 in the FZ temperature display and 00 in the FF temperature display.

Hello
I have attached the technician sheet. You will need enter the unit into the diagnistic mode to determine which control to replace . We have found more EOC issues than touch pads, but you still need to verify with diagnostics. Matt Ace technician

Hello
Have you run the unit through the diagnostic mode ? See technician link below for any error codes . My thoughts are an issue with the W10145531 Assembly, Power supply or W10464535 Assembly, Keypad. Matt Ace technician

Hello
See the Bosh videos below on a similar model. I also have training manual links below. Matt Ace technician

Hi. Yes, this does sound like the brake is bad. I have ran into this issue before. You can lubricate the brake and it will fix the problem for a period of time, or replace the brake assembly. I have attached a video for this repair.

Hello
I would recommend replacing it verses cleaning it. See Viking rang video links below.