All Answers

Hello
See the manual link below. There is no way to increase the amount of water into this unit. It is metered by the control board and water inlet valve. Matt Ace technician

Hello, we are not sure about an error code :”161″ , please be sure you are reading correctly. However, we did find and attach the manufacturer tech sheet for your exact model# with all error codes and testing procedures provided by Whirlpool

Hi. I have attached a similar repair video to remove the display. I have also attached the service manual for your unit. Page 28 has disassembly instructions for the display.

Hi. I have attached the service manual for you. It will have diagnostics and troubleshooting. The diagnostics for the lid switch are on page 41

The most likely cause is some type of drain obstruction leaving some water behind and then causing an overfill condition . Make sure drain hose is completely clear and drain pump does not have any plastic/paper debris in chamber . I have located and attached the technical guide for your model.

I have located and attached the complete Wolf service manual for your model. All technical information available can be found in this attachment. The troubleshooting guide begins on page 35 and the technical data on page 44. The schematic diagrams begin on page 46.

You may have a bad oven temperature sensor. Be sure to inspect the connection wiring to the sensor and you can ohm the sensor out. (should be around 1100 ohms at room temperature). If the sensor checks out good it sounds like the bake relay on the main board is failing . The part number for the oven control board is EBR73710105. I would recommend always replacing the sensor with any new control. The sensor for your model is EBG61305801. We could not find the exact service manual for your range, however I did attach a service manual for an LG LRE30 series range that is very similar . Unless removed, your model does have a tech sheet located inside a plastic sleeve on the back panel of your range.

Hi. I have attached the tech sheet for you. It explains how to enter diagnostic mode. Let me know if the link does not work.

Hello
See the technician sheet link below. If you go to test #101 you will test the defrost heater & defrost circuit. Also make sure its draining properly as there is a recall on the drain kit. See the service bulletin link below. Matt Ace technician

Hello
I will need a model number to get a technician sheet. The model and serial numbers may be found in the following locations on your microwave.
1) Inside the microwave.
2) O the left side wall.
3) Bottom of over-the-range microwaves, usually near the back.
4) On the back of the unit.

Hello
If you are getting proper temperatures in both sections and the ice makers are in the on position, run the unit through the diagnostic mode. You will be able to see any stored error codes and run both of the ice makers through a harvest cycle. See manual link below for testing.

Hello
See the complete technician diagnostic manual along with the service bulletin and update kit links below. Matt Ace technician

HI. I have attached the service manual for you. I did not find any bulletins for this issue. I would also think the relay on the board is sticking as well. With the manual you can find and test the relay.

Hello
See video links below on screen removal. Matt Ace technician

Hello
This is a common complaint we hear on the newer products that are energy efficient. You will need to verify
1) They are using a rinse aid.
2) The rinse aid dispenser is working properly.
3) The vent is not stuck in the closed position due to a defective relay on the board.
4) On model with a fan, make sure the fan is operating.
5) Heating element , you already verified that.
We recommend to try a rinse aid like( Jet- dry). Rinse agents help your dishwasher rinse away residue that causes spots and film on dishes and glasses. Rinse agents for automatic dishwashers, such as Jet-Dry Rinse Agent, are designed to lower the surface tension of the water, causing it to sheet off the dishes during the final rinse. This has reduced our complaints substantially. Go to section 4-15 for more detailed information in the manual link below. Matt Ace technician

Hello
See links below for manuals and service bulletins we have for your model. Matt Ace technician

Hello
See the technician diagnostic sheet link below. You will need to start with running the unit through the diagnostic mode on page #1. All of the error codes are listed on pages 3-6. Matt Ace technician

Hi. I have attached a service manual on a similar unit. Check your model number with the model numbers listed on this service manual. Page 44 shows the error code F6, which is for Communication lost with wireless module.

Hello
See service manual link below on tub removal instructions. Matt Ace technician

Hi. Sounds like you have a bad hub. Part number WPW10402178. You will get an off balance load error when this part is faulty. I could not find a video on this. You only need to remove the wash plate to get to the hub.