Unit powers on without issue. I had set the timer on the touchpad (for testing purposes) by pressing 1 0 0 0 ( for ten minutes ) and then hit “start”. After I hit the START button on the touchpad, the timer was counting down without issue but the microwave was not on or activated. I could not hear the motor or the fan or magnetron or anything.
Could there be a bad switch on the board inside ?
- Guest asked 8 years ago
- last active 8 years ago
We have gone four times to repair this microwave. The customer complains that the microwave does not heat. Initially we replaced the magnetron and it was working. On the second visit we replaced the thermal fuse. On the third visit it was heating but a reset was done aswell as reconected wires to thermal fuse and unit was heating. On the fourth visit the unit was heating but a reset was done again. Now the customer calls is complaing that it is not defrosting and heating, any suggestions?
- mytechjoe asked 8 years ago
- last active 8 years ago
This microwave will shut off mid cycle. The control will stay completely blank and nothing will happen. If you leave it unplugged for a little while it will cut back on and functional normal for a few cycles. Is the the control board going bad, or is it the mag tube interfering with the board and shutting it down. Are there any test I can do to check this, as everytime I am there after I plug unit up it will work fine for many back to back cycles
- Guest asked 8 years ago
- last active 8 years ago
Hello I have a customer call kitchen aid microwave issue only half of the LED display is lite, and the micowave wont start when push start button customer says he reset main breaker and the micowave will work properly for awhile. Have no imformation on unit, all help appricated.
- Patrick's Appliance Service asked 8 years ago
- last active 8 years ago
I am getting power to the outlet but nothing to the microwave
- Guest asked 8 years ago
- last active 8 years ago
Unit dead, no display.
Found vent thermostat (diagram part 115) scorched with riveted terminals sloppy loose. Connecting wire and stake on terminal cooked.
Jumpered terminals and microwave worked fine.
Ordered part three times but it keeps arriving N.O. Instead of N.C.
What could I be missing or where can I get the proper N.C. Thermostat (150degrees) I believe?
- Guest asked 8 years ago
- last active 8 years ago
from time to time cooking time will appear on the screen the microwave will not be working.
just the numbers will appear.
- Guest asked 8 years ago
- last active 8 years ago
The touchpad buttons on my Whirlpool microwave are unresponsive.
- Fred Abernethy asked 7 years ago
- last active 7 years ago
The handle on my GE microwave is loose.
- T&G Appliance Repair asked 7 years ago
- last active 7 years ago
I need to replace the turntable motor. Could you please give me service manual or job aid for Whirlpool microwave/oven combo unit model number woc54ec0as00? Thank you.
- mdhomeservices asked 7 years ago
- last active 7 years ago
there is power going to the board but nothing happens it is a Kenmore
- Guest asked 7 years ago
- last active 7 years ago
My microwave stops running after about 10 minutes of use.
- Patrick's Appliance Service asked 7 years ago
- last active 7 years ago
My whirlpool microwave is making too much noise.
- T&G Appliance Repair asked 7 years ago
- last active 7 years ago
My Whirlpool microwave does not always heat.
- Fred Abernethy asked 7 years ago
- last active 7 years ago
My microwave stove quits running after a few seconds.
- T&G Appliance Repair asked 7 years ago
- last active 7 years ago
Door handle loose how do I check or tighten hardware inside door
- Guest asked 7 years ago
- last active 7 years ago
Ordered both tension rods. Installed new ones door still falls.
- Guest asked 7 years ago
- last active 7 years ago
My customer has a GE Profile JVM2070SH001 Microwave and reports that the lights on the touch pad light up when the door is opened but non of the buttons will work when trying to start the microwave cooking cycle. any ideas will be appreciated.
- Keith Nelson asked 7 years ago
- last active 7 years ago
it seems that the microwave needs a new mag tube and diode.
- Guest asked 7 years ago
- last active 7 years ago
How do I access all the components to fix magnetron diode fan capacitor and HV CAPACITOR.
- Guest asked 7 years ago
- last active 7 years ago
How do I gain access to springs.
One door spring broke, should I replace both?
Access to replace springs. Video etc.
Do I have to watch out for fragile ribbon cable on top panel that can crack.
- Guest asked 7 years ago
- last active 7 years ago
- Guest asked 7 years ago
- last active 7 years ago
I found the primary interlock switch faulty on arrival, replaced and still had the same issue. The fan that comes on when the magnetron is active is only turning on when you open the door. I confirmed all the micro switches were functional at this point. My experience in the past is that one of the switches would cause this. I am suspectin that I am missing something here.
- Guest asked 7 years ago
- last active 7 years ago