Brand: Frigidaire

I have it turned all the way up and it’s not getting cold as it should . I have had it 9 going on ten years.

My ice wouldn’t come out so I aimed my hair dryer up the despencing hole in the front. Held the rubber black flap up with a wooden spoon and I think I knocked it out of what ever holds it in place because it won’t work now and you can move the piece up and down. how do I get that put back in the slots>

Could it be something stuck in dishwasher? Not quite sure how to access mine and clear anything out.

Is this my thermostat causing problems or maybe the control? I need to get this going for the holiday. Would appreciate some help.

I’m getting an error code on my oven display that I looked up and it says it’s for the probe? But my husband checked it and it is working properly. So what do we do now? I don’t want to replace it anyway if it’s fine.

Our oven worked perfectly through Thanksgiving (thank goodness!) but last night I’m pretty sure it didn’t heat up to the preheat temp even though it said it had and beeped as if ready. Dinner took much longer than normal to cook and I’m wondering if something isn’t right. I’m going to have my boyfriend take a look at it if someone could point me in the right direction on what to check?

I apparently have the same problem as shown in your video. What is the part number for that part? If it’s not available, what would be the part that would work?

Hi, I would like to follow the repair instructions from this video: https://www.youtube.com/watch?v=k1KEfcNfcMo

But I do not know which tools to purchase, could you tell me the name of the tools used?

Thank you!

So I have a Frigidaire refrigerator from 2009 that seems to no longer hold a steady temp in the fridge section and even when I turn the thermostat to make it colder it will turn on for about one minute and then shut off and then 3 minutes later do the same thing over and over again. There is no ice build up in the freezer and that is holding a steady temp of around 20 degrees but will not get colder than that. The fridge side will not get colder than 40 degrees and will flutcate between 40 and 45 depending on how much we open the door. Even the coldest setting on the thermostat there in no change in the fridge temp or freezer temp as well.

I saw the videos on clearing the chopper and sump area, and I checked the pump as well. I removed some debris thinking I’d solved it, but same thing happened on next load. Not sure where to go from here.

Hello, I was directed here from youtube to ask a question.
All of a sudden my waseher does not start at all,whether to fill,agitate or spin. I checked the power source,all is fine with my house. I was thinking it maybe overheated,but it still does not start.Then maybe I thought it might be a lid lock switch,although when it worked it dispensed water with the lid opened. Will that switch determine if washer starts at all?
Any help is greatly appreciated.

how to trouble shoot, the ice maker that is not making ice at all

I turned off the refrigerator because I had ice build up on the bottom of the freezer. I tried to turn it on a few hours later and it would not start. It beeped and did not turn on. Now it doesn’t stop beeping and the display is turned off.

the display on our stove keep doing this and I don’t live near any repair services that are reputable. What is the problem? I want to fix it myself.

I normally go in and open it up to take a look, see it hasn’t spun out again and try it again. Sometimes it works, sometimes it doesn’t.

Is this it’s own element or do I need to replace both on that side? We use it occasionally and I’d like it working again. Thanks for any help.

My neighbor thinks it’s something to do with a board or the electronics failing.

Hi,

My Frigidaire Professional series dishwasher is about 9 years old and has been a great dishwasher thus far, no issues whatsoever. in fact, i have 2 of them installed (1 on each side of my sink in the kitchen). One of them made a strange noise (it was not running, in fact it was empty and nothing at all was illuminated on the control panel). After the noise, i looked over and smoke was coming up from right at the top where the unit latches. The smoke smelled electrical and as long as we kept the door latched it continued to smoke, so we had to leave it open. I have taken the cover off and the control display off to reveal the control panel inside. There was indeed black stains on the white box which i guess would be the control unit.

My question would be, should i replace the entire ‘control unit’ of this dishwasher as the best way to potentially resolve this issue and have a functioning unit again? Currently now, nothing shows on the control display as though it has completely shorted out.

I have so much laundry to do and need this taken care of. I had my husband check the fuse and thermostat after seeing another question similar to mine. If I can get the correct part I think I can handle fixing it myself. Thanks!

My Frigidaire Professional FPHD2491KF buttons don’t work. Well only two light up when I press them. The start button does not work so I can’t run the machine. Would that be a console assembly problem or a pc board problem? How would I find out which one needs to be replaced as I have searched many forums and websites indicating that it can be either the PC board or the Consol assembly (panel where you press buttons) Thanks!

I changed the door gasket thinking it would fix it, but doesn’t seem to be sitting correctly.

Starts and after about 5-10 mins the dryer stops and starts beeping with D68 on the display, if you press cancel and start it again it will run for another 5-10 mins

I have a Frigidaire oven M#PLCF489ACB – no bake. The bake element test good for continuity. When put in bake mode, the broil comes on , but the bake element does not come on at all.
I feel that this will be the EOC, because if it was a thermal fuse/cutoff, then the broil would not be working. Cannot find wire diagram with the unit.