Brand: Frigidaire

ADC ADAPTIVE DEFROST BOARD PCB traces bad near orange and red wires for compressor one trace no continuity to relay on PCB board.

Customer call have a Frigidaire range FED355CCBC has a code F 3 can anyone tell me what this code means ?

Unexpectantly the dispenser hatch rapidly opens and closes and if the dispenser is set to water it comes out each time the dispenser opens and closes. What is the cause of this problem? The customer said she googled it and found it is a common compalint. Is this so?

The main problem is not trickling water but that whenever the dispenser WANT’S TO; ALL ON IT’S OWN ACCORD it , at any time opens and closes its hatch for 10 second’s or more then stops. Without ryme or reason. Wouldn’t this be a circuit board issue? and call for replacing it?

I have an issue with a Freezer, it’s a Frigidaire and this is the problem I am seeing: Intermittent cooling

Never had to replace one of these motors just need a video so I have some idea where to start. Thank you for your help.

so the temp in the freezer is not freezing.
i open the back unit the coils are frozen .
i put the unit into defrost and i can hear the ice melting . however i believe there is too much ice for it to melt before the cycle is done.
i tested the timer and it went back into a normal cycle what can the issue be?

Ice maker not making ice, I replaced ice maker, ice maker fan and ice maker defrost limit, I can’t get the fan to run. the ice maker will fill with water but will not freeze. it will cycle but will not freeze so it dumps water. the ice evaporator is working not frosted up. I think it will work if the fan would run.

My Frigidaire washer will not start.

THE CUSTOMER IS TELLING ME THAT THERE IS HEAT, BUT THE DRYING IS TAKING TOO LONG. I DID NOT GO TO SEE IT YET, COULD SOMEONE WALK ME THROUGH THE DIAGNOSIS? THANK, TODD FROM NY.

My customer is complaining that their refrigerator stops cooling/freezing every two weeks but after like 12 hours it will start cooling without the customer doing everything. The main control board has been changed but it happened a couple weeks after it was replaced.

I repaired fill tube dripping on to the evaporator
fan motor. Now the refrigerator door alarm is beeping open but is cooling fine and door are not open.
Freezer light switch is working as it turns the bulb on and off.
Logic would point to board, but normally the control has cooling issues when bad?
Has anyone else run across this problem?

Try star and show open door i replece the diir swicht and nothing happen any idea

My Frigidaire microwave is giving off a burning smell when in use.

The Frigidaire front loading washer will not spin. it let in just a bit of water and then nothing happens. ive unplugged it and checked that the water supply hoses are not clogged. what do i do next?

We have washer that will not pump. We have had two experienced technicians that are stumped on why this unit that will not pump water out of the tub. There are positively no restrictions as we completely tore the unit down to the inner and outer tub two different times by two technicians. We installed two different new pumps by both technicians. We have 115 volts to the pump and the pump is running. We can sometimes get the unit to pump out if we squeeze on the pump hose 3-4 times and prime it, the water will then will completely pump out. The next time fill and pump, it will not pump out at all, even with 115volts to the pump and clearly hearing the pump run. We have tried to pump the water into just a tub next to the washer thinking the drain could have back pressure or the drain hose in too far. We checked filter and check valve totally clear. We would like to know if anyone has run into this issue, I am sure we cannot be the only one. We are not factory certified Frigidaire and want know if there is recall on this specific pump part number below. Unless anyone else has another suggestion from what we have not tried already.

Thanks in advance for any suggestions

My Frigidaire washer is not draining properly.

Frigidaire Dishwasher GLD2440REQ1 the display show CL even after starting a cycle. Then a minute or two later the display flashes 96 and CL very rapidly. This just started a couple of days ago.

I need a service manual to test this unit. I’ve never seen this one before. Is there a way to test the temperature in the ice room? If it is turned off should the temperature be in the 40’s? I ran the checks in the tech sheet and it does move and the fill valve works but I don’t understand the principle of operation. I need to know how to disassemble it.