Washer works, but in spin cycle (small to large loads) washer is unbalanced.
- Apache Warrior asked 6 years ago
- last active 6 years ago
For the last month, customer has been seeing a thin layer of ice at the bottom of his ice bin. Hit test button and it seemed to work fine. Dumped and filled. No spill over or leaks that I could see
- Guest asked 6 years ago
- last active 6 years ago
I have a Kenmore front loading washer, about 8 yrs old, that has had what sounds like occasional bearing noise lately during the spin cycle. Today during the final high speed spin there was a bang and the drum slowed right down. I think it broke something… could this be related to the bearings? When I turned the machine off the drum didn’t seem to have a problem rotating back & forth very slowly for a while like it usually does at the end of a spin. If it is the drum bearings is it an expensive repair? — if it is I’m wondering if I’d be better off getting a new washer.
- Harley Clark asked 5 years ago
- last active 5 years ago
Washer fills then sets off tE error and eventually drains. No spin. Need tech sheet.
- Guest asked 4 years ago
- last active 4 years ago
What are the reasons the capacitor keeps blowing? And how do you test them? The motor runs, the agitator moves freely and so does the drum. The drain pump is clear.
- Guest asked 10 months ago
- last active 10 months ago
after I purchased my new home I cleaned my refrigerator and freezer out really good and I think I may have got water somewhere and potentially blew a fuse because before I cleaned it the ice dispenser and water dispenser both work finethe ice maker control light blinks twice stops for one second then repeats I’ve made sure that there was no obstruction to the optical part and still blinks twice what is the problem?
- eric asked 10 years ago
- last active 10 years ago
This is a he machine and unfortunately I used some regular liquid tide detergent. I’ve since ran several cycles with no detergent, he bleach on self clean mode and cleaned the machine with he cleaner. I’ve also ran the diagnostic test and it won’t go past c7. It drains all the water and then tries to agitate for about 10 minutes and then starts to fill back up with water. It does not go past c7 on the diagnostic test. Can this be fixed?
- Mike asked 10 years ago
- last active 10 years ago
The mfr. date is 01/2004. Compressor runs, but does not cool. Would it be cost affective to repair? Not sure if there is a leak, bad starter or the compressor is bad. It is a top/bottom style, stainless doors, medium in size.
- Guest asked 9 years ago
- last active 9 years ago
- Daniel asked 9 years ago
- last active 9 years ago
I set my washer to run, it fills with water, starts to wash and the timer advances to completion in about 3 minutes. It does not do the spin cycle but he states it does drain. Any ideas what this might be? Thank you in advance.
- Don Kopecky asked 9 years ago
- last active 9 years ago
- Guest asked 9 years ago
- last active 9 years ago
I removed a ceramic piece of dishware from the drain pump, the unit drains really slowly now. I made sure nothing was in the drain hose and explained to the customer the debris caused an issue with the pump. The unit also needs a new heating element which I had on me. Do you guys carry the pump? They opted not to have it done right away but I have a feeling I’ll be getting a call back soon to do it since any debris or foreign objects are going to slow down that drain pump even more. Really appreciate you guys being available to help us on the weekends! Unheard of in most service industries.
- Curtis Appliance Repair asked 9 years ago
- last active 9 years ago
My gas Kenmore range will not preheat.
- Patrick's Appliance Service asked 9 years ago
- last active 9 years ago
My Kenmore washer will not spin or agitate. I see little plastic and rubber pieces on the floor under the washer . What cold this be ?
- Don Kopecky asked 8 years ago
- last active 8 years ago
My electric Kenmore dryer is not heating properly.
- Patrick's Appliance Service asked 8 years ago
- last active 8 years ago
My Kenmore refrigerator is not cooling is the fresh food section and has frost on back coil.
- Harley Clark asked 8 years ago
- last active 8 years ago
no stove top action, oven works great,,,,, whats a poor boy to do ???? seriously,,, where can I look up codes?
- Guest asked 8 years ago
- last active 8 years ago
got a combo Kenmore washer/dryer, there is a11/2inch gap between the washing basket and the body at the top causing articles to full into the washer and mess up the drive belt and speed sensor, the real question is where does the speed sensor and bracket attach and secondly if there should be a gap at the top.
- Guest asked 8 years ago
- last active 8 years ago
the two lights were and the unit would not do anything.
I turned of the power and disconnected the ribbon and then reconnected it.
the unit started to work.
buy I still see the lights slightly on
- Guest asked 8 years ago
- last active 8 years ago
I have a Kenmore Refrigerator that is not working.
- Harley Clark asked 7 years ago
- last active 7 years ago
The ice chute on my refrigerator is frosting up.
- T&G Appliance Repair asked 7 years ago
- last active 7 years ago
I checked the continuity on the heating element and the thermistor. Both were dead. No continuity.
Is the thermistor supposed to show continuity?
- Guest asked 7 years ago
- last active 7 years ago
The washer is spinning, but the clothes are still wet. About 6 months ago changed out pump because it was not draining. Is there an actuator or a motor sensor?
- Apache Warrior asked 6 years ago
- last active 6 years ago
I have a coustmer that has a ice maker that keeps frezzing sears came to her house when it was still under warranty and told her to defrost ref and it would fix itself so she took all her food to next door nabors and defrostrd it it lasted 6 months and did it again so she went to nabors and asked if she could leave food and defrosted it again but this time it only lasted about 3 weeks she is very upset with sears and hopes that they go out of business soon
- heritage asked 6 years ago
- last active 6 years ago
Looking for manual so I can figure out why machine will not go into spin mode. It’s a Kenmore washer model # 110.26002010
Thanks.
- mdhomeservices asked 6 years ago
- last active 6 years ago
Do you have the service manual for this washer?
- Guest asked 5 years ago
- last active 5 years ago
I replaced the door latch. It takes a while before it releases after stopping or finishing a load and will not unlock for a while, it just keeps clicking.
- Guest asked 4 years ago
- last active 4 years ago
This icemaker won’t make ice. It fills but doesn’t harvest cubes.
- Guest asked 8 months ago
- last active 8 months ago