Brand: Kenmore

Dishwasher motor doen’t run, Drain works when you it cancel. Unit won’t go into diagnostics. Is there a video that shows you how. I tried any key 3 consecutive times within 1 sec. closed the door. won’t go into diagnostics. Does the tubulity sensor have anything to do with motor running? I’m sure if i’m doing it right to put to diagnostics. They say it has to be in stand by mode. Is stand by mode the pause button or is it with the door open and the start button pushed. It would be really helpfull if they have video on how to put into diagnostics.

The problem is that someone changed the front left burner (3 stage) and they put the wires in the wrong order. I have a new burner and I would like to know which color wire attaches to which pin on the burner, the colors are Orange, Blue and Grey., and there are 3 pins on the burner. I am concerned with attempting to go on a peck and find method in case it damages the new burner.

I posted a question about a week ago and I checked the refrigerator drain and pan and they are clear and the water tank also. The water is coming from the refrigerator room at the bottom on the left side where there is a vent and damper control. Where does the air supply come from for that vent? I am not talking about the vent in the back. near the water tank where the fixer box and fan is in the rear. The water under the drawer comes from that front vent. The customer says it is often iced up.

making noise when running?

I HAVE TWO, OF THESE UNITS, WITH SEALED SYSTEM PROBLEMS. PREVIOUS TECHS CUT NUMEROUS REFRIGERATION LINES. I NEED INFO ON PUTTING UNITS INTO DIAGNOSTIC MODE, SPECIFICALLY IN PREPARATION TO FINDING LEAK OR LEAKS AND RECHARGING. I NEED TO GET THE REVERSING VALVE IN THE CORRECT POSITION, ETC

The compressor is running and pulling 1 amp. the condensing coil is clean and both fans are running. I installed a service valve, on the suction line, at the compressor. when i attached the gauges it immediately went to 29 inches of vacuum. I unplugged the unit and it stayed at the same value. in your opinion what does this indicate. i’m waiting on r134a to be delivered so I haven’t tried adding any refrigerant to this point.

I had a customer with a Kenmore standup freezer and not getting enough cold on both food compartment and the freezer. We just replaced the control board and still having the same issue.
Your help is very critical. please assist.

why is this unit not making ice cubes

i changed the air damper and it still will not blow cold air to the fridge but when i open the freezer door i will get cold air in the fridge true the damper.
also there is alot of frost around the ice maker machine

I was recharging the compressor with refrigerant and the compressor was hot but during recharging the compressor just shut down.

The cild air Only flow into the refrigerator through the damper when the freezer door is open when I close the freezer door and put my hand in the refrigerator near the damper there was no air flowing

so i checked up what the blinking light read and it came to F5E3
hoe ever the unit did run once and then it stopped i can hear the drum trying to turn and then shots off can it have to do with the timer as well?

Ice up on evaporator, refrigerator not getting cold.

what dose it mean and how can we fix it

so i put in into diagnostics mode and i got an error of F6 E1
how can i repair this?
its a Kenmore washer

  I went out on service call on a Kenmore bottom freezer/refrigerator. I would like to know how to get the pcb in diagnosis mode. Thanks

washer has the F25 error code stored 3 times & F17 store once.

History, the MCU was replaced. Customer ran 2 loads fine and now error codes back. I watched it run a complete cycle with large load of towels yesterday, no issues. This AM, the F17 code came back, customer left it right where it stopped. Load of towels drained but not spun out.

Problem is the tech sheet in washer has no F17 error code. Looking around online, someone suggested the user interface. I am loosing my sanity on ordering these parts and then wait and see if that was the fix!

ALL connections checked, wires ohmed, tach on motor ohms correctly, drains fine, pressure hose clear, no suds. Here this AM watching it again and working fine.

Anyone else come across this F17 code?

We are working on a Kenmore (standard Whirlpool design) SXS
Model 106.57032601 with dispenser. Ice bucket is mounted on door.
Flapper door is shutting properly and sealing. Motor is working to drive cubes. 3X
in 4 months have found ice clog inside the ice chopper mechanism. We clear it and
it works great for about 2 months then plugs again. Ice looks partially fused by
melting. Auger motor then sounds stripped when clogged but works okay when
jam is cleared.
Does that auger motor sound stripped when jammed then work when not?
Do you think the flapper is sticking open and which of the flapper doors parts would be suspect?

Thanks in advance

Model – 253.54373300 built by Frigidaire

Looking at parts breakdown, I see there is a refrigerator damper assy ( 241600902). Wiring diagram at Sears web site is too small to read.
Does the defrost temperature control ( 5303918476 ) activate damper assy.? Looks like thermostat control is old style with a capillary tubing.

it will agitate but will only spin if i start turning it by hand