All Answers

Hello
See service bulletins and diagnostics sheet link below. You may have the Helix riding up the spline shaft of the transmission causes noise during agitation. Matt Ace technician

Hello
See video below on Frigidare motor replacement. Its not the exact model but should help you complete motor replacement. Matt Ace technician

Hello
See video links below. I can get you a service guide if you give us a complete model number. Matt Ace technician

Hello

See service manual and service bulletin for ice maker link below. Matt Ace technician

Hello
See service manual and service bulletin links below. Matt Ace technician

I have attached an information link for you. Page 29 is the mode shifter coil and inverter test. The few pages before and after all have good information as well. Please note that some testing readings change by closing and opening lid. Also are you sure that the lid switch has not failed.

Hello
Are you sure the inverter board and mode shifter is off the same model ? That can be an issue if its off another machine that is not compatible. Matt Ace technician

Hello
Testing fresh food ice maker Press ٨ and ٧ temperature pads for up to 10 sec. simultaneously.
Press + or – to move forward or backward through tests.
Deactivate: Press + for up to 10 sec. FFIM Diagnostic Mode will automatically deactivate after 5 min. of inactivity.
NOTE: Silence alarm.

Test To activate test Passing Result
52C Ice Maker Thermistor Activates automatically

FZ display shows temperature sensed by Ice Maker Thermistor.“OP” if open; “SH” if short

55C Water Valve Set Remove ice tray to collect water into a measuring container to measure water
fill. If collecting water into ice tray, first perform test 63C to empty ice tray.

57C Evaporator Fan (FFIM) Set “On” on FZ display when fan activated, “OFF” when deactivated.

58C Remove ice bucket. Allow bail arm to drop freely. Pass if no alarm when tray returns to “home” position.
Hold bail arm up. Pass if alarm sounds when tray returns to “home” position.This test runs continuously until another test is selected. Ice Level Sensor Activates automatically. This test runs continuously until another test is selected.

Remove ice bucket. Allow bail arm to drop freely. Pass if no alarm when tray returns to “home” position.
Hold bail arm up. Pass if alarm sounds when tray returns to “home” p

63C Twist Tray Set. Remove ice bucket. FZ display shows “1” and “GOOD”.
See Diagnostic link below. Matt Ace technician

Hello, if the compressor is running and you have zero frost pattern then you will have a sealed system issue, You need to tap into the system to see whats going on. I could not find a video on this model but hope this video helps.

Hello, if the compressor is running and you have zero frost pattern then you will have a sealed system issue, You need to tap into the system to see whats going on. I could not find a video on this model but hope this video helps.

Hello
The unit needs to have equalized pressure on the high and low side of the system before the compressor will start. If it is not properly equalized the compressor will cycle off on the overload. If the pressures take too log to equalize you could have a restriction in the capillary tube or filter dryer preventing the system from equalizing. A normal time to completely equalize should be 2-5 minutes. Matt Ace technician

Hello
See diagnostic guides and video links below for your model. Matt Ace technician

Try under the old part number 280145. If it stripped out that soon, most likely the tub is not fully engaging and hanging up on the shaft. May need to replace the seal, bearings, and shaft kit W10435302. See technician diagnostic sheet below. Matt Ace technician

The H1 Error code is a Freezer Temp. above 26ºF . Circuit E2 Description The electronic control board detected a touch keypad error. Solution Reset the control and test for stuck keys. If error code returns, replace the touch keypad assembly. Matt Ace technician

Hello
See service information and videos on your issue below. See diagnostic guide links.

Matt Ace technician

Hello
See service manual link below with wiring diagrams starting on page #83 . Also see fast track troubleshooting guide link below . Matt Ace technician

Hello
The (UL) Error is displayed when the machine/motor control detects an off-balance load, and is
steady on while the washer runs a mini-cycle to re-balance the load.
➔ Display clears if mini-cycle successfully
re-balanced the load.
➔ If the mini-cycle is unsuccessful, UL will
flash until the door lid is opened, allowing
the customer to view and redistribute the load.
See Complete technician diagnostic link below Matt Ace technician

We have a video that steps you through this very issue. View the video linked below

We have a video that steps you through this very issue. View the video linked below