Brand: Kenmore

I am looking to replace the heating element on my dryer. I am not sure where the element on this unit is located, any ideas?

FF & FZ not getting cold enough. I would say because the compressor is not staying on long enough. Its a linear compressor. I measured the voltage going to it. 220v when starts and slowly rises to 350v then shuts off o volts. 5 minutes later will start again. compressor is normal temp not burning hot. looked at the main board, its giving 6 flashes. Evap. & Condenser fans stay running. Only the compressor shuts off. voltage at the wall outlet is normal 120v.

Shuts off and gives error codes.

I have a kenmore fridge 970 top freezer that is leaking water inside accumulating on the bottom. From what I have read it could be a plugged drain hole for the freezer portion but I dont know where it is located.

Washer works, but in spin cycle (small to large loads) washer is unbalanced.

Freezer section does not get down to 0F as it should. Mainly stays around 20F. Fresh food compartment sometime freezes item in the back on top shelf, otherwise section is cold enough. Does seem to run a lot but does shut off for long periods. Compressor is pretty warm but not “hot” to the touch. Lower fan at base is working, upper fan is working, pumping cool air into both sections. I have cleaned the cooling veins twice and would say there are a clean at I can get them.

Fridge not cooling and control temp board not working

Have a refrigerator with broken wires at bottom of freezer door. This is causing the ice maker not to run. Is a new wire harness available and any info on how to replace.

This kenmore elite is leaking water behind the icemaker. Coming out of upper part

board part# wp8524212 I would like to know if you have a video how to removed this board.

fast wash which is a 30 minute cycle goes down to zero and then it turns back on again and went to 15 mins cycle…. for the 15 mins cycle then goes through another wash cycle….so the 15 mins wash it went down to zero and everything drained and there is no water in it now so it works on the 15 min cycle and not the 30 mins cycle (wont turn off on 30 mins but shuts off on the 15 min cycle)….for the 30 mins has to shut off manually which then leaves water in the dishwasher

I did not see the washer yet, but the customer tells me that the spin cycle starts at 13 minutes. At 11 minutes it will start to fill with water. She has to shut the water in order for it to drain and spin properly.This problem happens about 50% of the time. Any help would be great, thanks.

I know some Kenmore refrigerators are made by LG or Samsung can you tell me if this one is made by either one of those companies? If it was by LG or Samsung what is there corresponding model number?

WASHER DOES MAKES A LIGHT KNOCKING SOUND DURING WASH CYCLE.

MACHINE DOES WORKS. DISPLAY “AF” ERROR CODE.ELECTRIC DRYER.

The washer is spinning, but the clothes are still wet. About 6 months ago changed out pump because it was not draining. Is there an actuator or a motor sensor?

The heating element has burned out 4 times. The last 2 times they burned out faster than previously. Each time the element was replaced.

dryer not heating , changed thermal fuse DC47-00016A worked hour later customer called no working agian .

The tech sheet is missing . Any videos on this code also

This dryer has had several new parts replaced. Thus: new control board, new touch pad, door latch, heating element, thermostat, cut-off thermostat, thermistor, new drum belt.
What else, do you think, needs to be done???

This model is 14 years and does not have the temperature control that causes the same symptons. It does have a small circuit board to control the temperature but when I unplug it it still does the same . If I run it on second rinse it does not spray and soak the clothes.

tried new pump with old board and old board with new pump and new pump with new board same issues

Closing of French doors or freezer drawer hear a high pitch noise. Doesn’t run long enough to hear where it coming from.