Brand: Whirlpool

So my refrigerator is completely broken with the cold air switch not functioning and the lights don’t work. The cold air functions a little only when i turn it off but when i put it on low-medium-high setting, it completely does not work. The three lights do not work but the light bulbs are brand new. To resolve this, i replaced the bi-metal defroster and defrost timer for the refrigerator. But the results are the same and my refrigerator is still broken. Any suggestions as to how i can fix this?

My washer is making some very unusual and strange noises during it’s cycle. I just got it not long ago and I don’t ever remember my old one sounding like this. How would I know what’s normal and what might be a problem? Should I have a service call on it just to make sure? I’d hate to let something go that could cause damage down the road.

Our dryer seems to be getting too hot and then shutting down. Normally I can wait and restart it to finish a load but not always. We’re on a 2nd story of a duplex and I tried checking the outside venting, but it looked clear where it exited the house. Any other thoughts? Could the hi limit fuse just be going bad? Or maybe the thermostat?

Our dishwasher comes on, lights up, and fills, but then won’t actually wash. It just stops and there’s almost a low hum noise. My husband got it to cancel and drain and I redid it thinking it was a fluke, but exact same thing happened. What should we do from here?

Didn’t get any voltage across the heater element terminals on my WED9470WW1 Duet dryer. Pulled wires from high limit thermostat and thermal cutoff on the heater box. Got continuity on both. The heater element had continuity as well when tested with its wires removed from the terminals. Getting 240v from the outlet. Don’t know what to would be most likely culprit to check next. On the blower housing, the fuse has continuity, the only weird thing I found is that the thermistor has a resistance reading of 14k ohms. in 70 degree room temp. Heard these should be around 12k ohm. Could this cut the heat? Or is controller or controller relay higher probability of fault? Can the controllers relay be tested? BTW best video on the topic. Thank you !

my freezer quit working. i ordered the board and replaced it, with it came a new touchpad and it said i have to replace it also. how do i do that..

I’ve got this thing apart and have been checking parts to find the problem. It was tripping the breaker consistently and now I’m not sure what’s causing it. Checked the board, seemed fine. Checked the igniter, also good. Getting proper power to and from unit and the wall, so can anyone help me out?

The water dispenser in the door gives me water for a very brief couple seconds and then just trickles out like it’s not on or something. I seem to still be getting ice made so I have no clue as to why the door won’t give me water. What can I check to figure this out myself?

I keep finding them and don’t want them to get stuck in the pump. Can I clean out the drum somehow?

My washer fill but doesn’t start to wash or agitate after it fill. It change the light from fill to wash but stay that way and do nothing. If I put it on spin and drain it works great, so I believed that the motor is ok. When the machine is performing it locks the lid. What could this be, and how can i fix it? Thank for the You Tube help!

Burner comes on for 10 seconds and cuts off. Clothes never heat up enough to dry.

do you think the 25 amp fuse would be the most likely of the problem?

Serial # SJ3751348, built in Sept 1999. I cleaned a ton of dust off the coils first. Still won’t get cold. The fan motor is working and airflow is coming into the fridge and freezer. I hear a clicking noise coming from the plug on the side of the big black pot with copper tubes coming into it. Every 3-4 minutes I hear an initial “click”, then nothing happens for about 1 minute or so, then another “click”. Sounds like a relay opening and closing, but nothing else happens.

washing machine has error code and will not work. Couldn’t find what it means or what we’d need to do to fix it.

I thought it was odd that our stove tripped a breaker, as soon as I reset it, it seemed fine. What should I check on it to ensure it doesn’t keep happening?

Our washer has a very slow but steady drip of water inside the tub, even when not being used. I checked the connections, and everything is tightened. What should I do to stop it?

We have watched and repaired/replaced drain tube. However, we still have ice forming on the floor of the freezer and are wondering if we need to defrost the drain line and how to do it.

Not sure if the dispenser is broken or if it needs cleaned out but I’m not very knowledgeable about appliances. Any help would be great.

Power O.K. to terminal block. No Lights, Nothing Works.
Replaced main control board per troubleshooting guide supplied with dryer, but did not fix problem. Dryer will operate fine once (infrequently) then nothng works after that. Checked through to control panel connections..everything is clean and tight, Dryer would not work after replacing main control board. Put old board back in and it worked for one complete cycle. Then no lights and no start situation again.

Door switch clicks crisply and seems O.K. but haven’t tested due to access.. Light comes on inside drum when door open and off when door closed.. If I need to remove back panel I need help with how to remove “clip” at vent opening….can’t figure how to unclip.

There are two boards inside user panel….nothing burnt, all looks clean and fine except a tiny bit of corrosion on the board side of the wide ribbon cable. (cleaned and WD-40).

If I remember correctly, both times that the user panel lights came on and dryer worked was directly after I had thrown the main fuse (at the main house fuse box) off and then on, but I have been unable to duplicate this scenario.

Please help, and if I have to remove back panel from dryer cabinet, advise how to unclip the clip at the vent opening.

Thanks

We need some advice on a Whirlpool washer WTW4910XQ0.
When the unit is running the belt keeps sliding down and coming off.
Any advice would be appreciated.

We have a very strange problem with this washer, Whirlpool ,mod.WFW8400TW00
It leaks in the clean cycle only . Couldn’t find the source of the leak
because dryer is on the top of the washing machine ,located in the very small room .
Anyone knows about the source of the leak in the clean cycle so we can save our time
without going back and forth ?
Thank you

Complaint: Unit taking very long time to complete cycle and or pauses with water,
but will complete cycle. This unit is located in a Seminary with multiple users so can’t get proper feedback. Any help appreciated.

There is a sturdy piece of plastic where i though the grommet should be and i am afraid to pull it out because i might break it.

Having a problem removing the icemaker on thid box. model GI6FDRXXY03
Wire harness cover comes off and latch holding icemaker in moved easily but the icemaker will not move.

Anyone have a manual on this frig.