0 votes
955 views

My washer is making a grinding noise.

0 votes
1k views
  • Guest asked 4 years ago
  • last active 4 years ago
1 vote
2k views

we need a video on how to dismantle the dryer

  • Guest asked 5 years ago
  • last active 5 years ago
1 vote
1k views

The customer showed me a video that sounded like the pump running with the door open. She said that it shows an error code often of 10 and last time it showed 30.
Where is the tech sheet hidden? I couldn’t find it behind the door panel or behind the toe plate.
I need a copy of it and the error codes and videos.

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
1k views

The door strike is ok. The Reed switch is okay. There is no continuity at J2 . The harness wires are good.
Do I need to check the wax motor.
I changed the door switch with a new one. Still the same. Lock error.
Is it the electronic control?
How could there be continuity at J2 with the door shut?

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
1k views

I need any info on this microwave you can give me. The customer states you hit the button, it beeps once and shuts down.

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
1k views

FRESH FOOD SECTION NO ICE PRODUCTION
FREEZER SECTION LOW ICE PRODUCTION CHECK WATER VALVE ELECTRICALL OK BUT THE WATER COMING IN TO THE WATER VALVE BELOW 30 PSI WILL THAT CAUSE THE ICE MAKERS TO NOT PRODUCE ICE OR LOW ICE PRODUCTION OF ICE I DON’T BELIEVE THE ICE MAKER CAN BOTH BE BAD ANY SUGGESTIONS ON WHAT TO CHECK

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
2k views

I’m trying to replace the main power board. replaced old board but the fridge dose not start up, no lights nothing, controls dead. I also replace the thermistor
Reinstalled old board fridge started up, lights working, controls working.
Installed another new board. nothing.
Fridge is also missing the tech sheet.
Initial problem, Items freezing items in fresh food section,
Thanks for your help

  • rfcorral asked 6 years ago
  • last active 6 years ago
1 vote
2k views

video on how to replace rack sensor

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
1k views

I’m not getting any power to my defrost t-stat. I know it’s the main board, but on this style with the user interface board on the side of the door, do I have to change the user interface board as well?

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

My dryer powers on/off via power button just fine. The knob selector also works appropriately. The start button does not always register being touched. Likewise, other “buttons” do not sense being touched (Temp, dry level, dry time, options, set, cancel). When the dryer does start, there is a lot of rapid beeping during the drying cycle. I cannot enter into diagnostic mode or perform a factory reset due to the lack of response to the key pad. I attempted to replace the UI board (part # 5304505611) but that did not resolve the problem. Last night, after managing to get the dryer started and run through a complete drying cycle, the unit restarted on a cycle without the unit being touched.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views
0 votes
2k views

I need a tech sheet and if this sounds familiar please advise.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views
  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
1k views

FFIM water tube keeps forming ice plug. I can break out the plug and ice maker resumes normal operation for about a week until it plugs again. Ran diagnostic mode on ice maker and everything seems to be normal.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

I have a dryer that will run 1 load and work fine then on the 2nd load just stops and the start button blinks. you can start it again but it will only run for 5 seconds or so and the start button will blink again. there are no error codes

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

Washer not draining or spinning, I got it into diagnostic mode and got it to drain, but still wont spin. Its reporting a 5A error. Not sure what to troubleshoot next.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

Customer was using broiler and they heard a popping noise and now nothing in the oven section works. I’m pretty certain this is a control board issue, the problem is, I have never worked on this style unit before. Any information/videos/on how to take this giant apart please send to me. I need to know how to get to the board.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

I have an Electrolux refrigerator model EI26SS55GWO. We have Reverse Osmosis water going to it which is filtered about 6 times more than the refrigerator filters yet it seems in order to keep the ice maker working properly the filter needs to be changed about every two months. Is there a way to by pass the filter?

0 votes
3k views

I just replaced the heater unit due to an Error Code 73. I am now getting an Error Code 91 some kind of communication issue.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views
  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
3k views

This is a Kenmore refrigerator that is built by Electrolux . It is a french door bottom freezer. There was a frost build up on freezer evaporator coil. We defrosted it and a week later it built up again. Defrost heater and termination switch checks out. What else can it be?

  • Guest asked 6 years ago
  • last active 6 years ago
1 vote
2k views

I need to remove the stainless steel trim ring that surrounds the ice/water dispenser. Do you have a technical manual showing how to do this? I don’t want to damage it. I don’t see any exposed screws.

  • Guest asked 6 years ago
  • last active 6 years ago
1 vote
3k views

Our Electrolux refrigerator dispenses ice intermittently. It spits ice out on the floor. We have had to shut the water off or it will spit water also. With the water off you can see and hear the dispenser turning on and off at all hours of the day or night. I need to dig into the parts to see if it is a loose wire or faulty control panel?

I need help with how to pull the stainless ring off the control panel to get at the parts.

Has anyone solved this issue before?
I have seen it reported as Casper the friendly ghost.

Thanks,
Tom

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
10k views

My Electorlux range is getting an E31 error code.

0 votes
2k views

we need to know how to replace the igniter

  • Guest asked 6 years ago
  • last active 6 years ago
1 vote
2k views

When I try to push start to get the control panel to light up. The display board just blinks and beeps once and won’t turn on. Its been doing this for a while and unplugging and plugging back in usually works but is not working anymore.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

Hello

We have an electrolux ewdw6505gs0 that we have had for about 6 years. Recently it stopped washing the upper rack as good as it used to. It’s not every time but appears to be more bad than good. I have removed all of the parts that the water passes through and have found no obstructions including the pump and hoses underneath. I am very handy and have an extensive set of tools so any repair or diagnostics necessary I should be ok to do. Dishwasher has never had problems until now. My hope is to fix it rather than have to shell out $800 for a new one. I suspect it could be a weak pump or a control board but I dont want to throw unnecessary parts at the problem you have a way I can diagnose what the issue is.

Thank you

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
13k views

The dryer powers on but doesn’t start. Pressing the start button gives 3 beeps almost like the door isn’t closed. I put the dryer into test mode and all I get is error code EHd, this doesn’t appear in any diagnostics codes anywhere. The control panel appears to be responsive. None of the error code sheets show this error code.

There was a large amount of lint being blown out the back of the dryer and I cleaned out the outlet. I’m about to take apart the bulkhead to get to the blower and vacuum that out too.

  • Guest asked 6 years ago
  • last active 6 years ago
Showing 31 - 60 of 202 results