why is this unit not making ice cubes
- Guest asked 7 years ago
- last active 7 years ago
The problem was that it was not making ice. It is a KitchenAid under counter ice maker. I put it through the self cleaning cycle twice and after it made ice, but then the customer called back saying it didn’t make ice after I left. When I went back I unplugged it for a few minutes then plugged it back in it would make ice one time then quit again. The ice maker does not have a tech sheet to run self diagnostics. Does anybody have a tech sheet or know where I can get one? Do I have a bad PCB? Does anyone know what is wrong with this? Also there is a ice wall in the back, is this supposed to be there? It is solid covering the back so I cannot reach back there without breaking it, which I do not want to do if it is supposed to be there.
- Apache Warrior asked 7 years ago
- last active 7 years ago
The brand in Manitowoc Ice Inc. I am not familiar with commercial icemakers, I got called out this one and I need your help. When the machine is turned on, the water will run over the vertical ice tray. The back of the tray is at zero degrees. A little ice does form on the trays edges. Also there is a cover over the vertical ice tray that opens to release the ice when in harvest. But right now when the cover is closed the water continues to run. How is the correct operation of this icemaker? Also is there a video that I could view? Thank you for your help, Ricky.
- Apache Warrior asked 7 years ago
- last active 7 years ago
Have issue with Scotsman ice machine. Contactor closes pump runs compressor starts runs no fan I think unit tripping contractor opens due to hi pressure. Check one side fan power from contractor and the other from main board not getting power from main board. The board is very expensive does anyone have information on unit all help appreciated
- Hall Refrigeration asked 7 years ago
- last active 7 years ago
K board has been replaced by two different techs ice forms drops sheet onto grid stays there when pulled amps on grid its .8 amps what is the normal voltage to cutter grid. Serial is k13507719 kitchenaid
- Guest asked 7 years ago
- last active 7 years ago
Getting error code 1 ? Model fc85a. Serial 000690 any ideas meister stand alone ice machine
- Guest asked 7 years ago
- last active 7 years ago
The Ice in my Kitchenaid icemaker is melting and clumping together.
- Harley Clark asked 7 years ago
- last active 7 years ago
I have an under counter ice maker and it has good water pressure to the unit but will not produce any ice. Where do I start the diagnoses ?
- Patrick's Appliance Service asked 8 years ago
- last active 8 years ago
I have a stand alone ice maker with the square grid wires.The ice will not produce and drop into bin.
- Hall Refrigeration asked 8 years ago
- last active 8 years ago
The unit fills up 1/2 way with ice.
My tech ordered an thermostat. Any help is greatly appreciated.
- Hall Refrigeration asked 8 years ago
- last active 8 years ago
One of my customers has a Summit model BIM44 which has been horribly maintained. I found everything scaled up, especially the distribution tube over the evap. Pump sounds like it’s running smoothly back there, but it appears the intake from the sump is blocked. I feel like it just needs a proper flush and cleaning. Any tips greatly appreciated!
- Fred Abernethy asked 8 years ago
- last active 8 years ago
I have a GE Fridge MN:PFFSS6PKWBSS, SN: AR075158. The IM produces a few batches of ice per day. The IM cycles when I hold down the cycle button for 10 seconds and it fills with water. The duct seems to have good airflow to the compartment and the sensor mounted in the back checks out fine. Any ideas?
- Patrick's Appliance Service asked 8 years ago
- last active 8 years ago
I have a model 3151 ice machine which had a bad cube size control. The new control looks different in its terminal designation, and the darn part came with NO notes on how to adapt to the new control. The old one had a 1, 2 & 3 terminal marking. The new one has 4, 5 & 6. Have no idea where to place the wires properly..anyone else been here?
- Antonio R asked 8 years ago
- last active 8 years ago