Appliance Type: Stove / Oven / Cooktop

hotpoint oven the oven and broiler not working

I have this IN WALL OVEN with an F7 E6 ERROR
From what I read it says control panel problem, I think it’s a membrane that has gone bad
But I can’t find a part number for that… anybody have a clue?

I have installed three sets of door hinges. I know these hinges don;’t work because I have run into a few of these stoves.
Has anyone heard of a solution to this? Whirlpool has to know about it because I had my parts supplier inquire a year ago. I had one customer that was ok with a latch on the side of his stove. Any suggestions ?
Thanks,

f3 e2 error when you use the micro I replaced the erc because there was no display now I get this code and I already checked sensor I was thinking about installing another erc

I’m trying to find the part information on a middle (center) burner electrode kit. I don’t even know if I can replace it without some help getting to it. But if you have some part information that would be helpful.

Replaced door lock after power on .after 30 seconds display F1 what F1 means

I have a a 48″ Jenn-air range ; customer complain that main oven flame was sputtering and shut off. They started smelling gas he called gas company they came out and said he had a gas leak. I went out and order a regulator. Replaced regulator unit still does the same thing all other burners are Ok could it be the safety valve?

Customer call have a Frigidaire range FED355CCBC has a code F 3 can anyone tell me what this code means ?

Control board and touch assembly replaced last month . Now the range shuts off after 3 min. in self clean. Thanks in advance for your response.

When set to bake, after about 20 seconds the unit codes out with f-34. tech sheet only says: replace air switch, then replace cooling fan, then replace control. all 3 have been replaced, in that order, and its still giving f34. the tech sheet doesn’t give any other information about the code. Anyone have any suggestions?

I have a 48″ Jenn-air range ; that main oven flame was sputtering and shut off. I started smelling gas and called gas company they came out and said he had a gas leak. I went out and order a regulator. Replaced regulator unit still does the same thing all other burners are Ok could it be the safety valve?

G E range # JGS968SEK1SS ordered a new control board, installed now the range has a code LOC REF unplugged range powers up LOC REF
2 seconds than all the led lights on board on for 15 seconds, than LOC REF appears again cannot clear, can someone help me with issue.

Wiring diagram needed for Frigidaire dual range Model# PLCF489ACB
I am having the board rebuilt by CoreCentric and would like to have the wiring diagram to make sure everything is wired correctly. I am not the first to work on this. Any help is greatly appreciated.I would try looking for a video at ApplianceVideo.com. Just type in your symptom and look for a free video.

GE Oven Model JKP45W0W2WW Original board part #WB27K5318 changes to part #WB27T10290. The configuration of wiring the terminals is different on the new board and there was no wiring diagram in the box. Expensive board I would hate to get it wrong. Does anyone have a wiring diagram for the new board? I’m told there should have been one in the box. Most of the confusion is with the common wires. On the old board the two common wires are marked C and Com. On the new board the markings are Com0 and Com1. The configuration of the new relays is different as well but I think I have that part figured out. The reason I am changing the board is the clock went blank and is unresponsive to the touch panel. The touch panel beeps weakly when buttons are depressed. Should I be looking for a failure in the oven that caused the clock failure or do these things just go out on there own. Oven was not in use at the time of failure and no self clean was being done at the time. The customer heard the oven make some sounds and went to check it and the display had gone blank. I know this was lengthy. Thank you for any advise.

Have a kitchenaid wall oven. Model KEBS107SSS04
Error code says to replace the ( UI ), I assume this means USER INTERFACE.
touch pad and pc display board. Neither are identified as a UI and both are costly.

When customer programs MW say for 60 seconds, it starts counting down 59 58 57 56 55 . When that happens, it quits heating and shuts off. He will cancel, and after a few seconds of heating and counting down, it stops heating and the count down just stays there.

Does this come with some kind of kit for the entire assembly? I think I need the valve and knob for it. Thanks for any information you can get me.

I don’t have a model number on this oven. I was working in this kitchen removed the oven door improperly and could not reinstall it. I pushed the hinges and set the catches and attempted to put the door back on. After a little effort I got it back on but then could not open it. The door is locked. I have tried a coat hanger to pull on the lock without success. I have tried setting self clean and then cancelling it and turning off the circuit breaker for a few minutes. I would be very greatful for any tips on how to get the door open. Thanks

—

This needs a touchpad but I can’t find the part lookup information for it. Thanks.

I checked the control it seems ok, so I’m assuming it’s the touchpad. Do you guys have some part information there you could pass along for this? Thanks.

This unit is not reaching pre heat or even maintaining any temperatures. Checked all the heating components and they are fine. Got to main relay board and found it bad, cannot find it in stock through my vendors, do you guys have it?

Looking for two Thermador hinges part # 00488417
Any help would be appreciated

I have a Kitchen Aid wall oven, electric heat. Model # KEBS107DAL4 – gives fault code:
F3 – E2 ( Oven too hot Replace oven temperature sensor)
This fault code only when self-cleaning. Bake and Broil works fine.
Wouldn’t the sensor fail for baking as well? Thanks in advance for any help.

Dacor Wall oven. Upper oven would no heat, lower oven working fine.
Double oven electric. Upper oven would not heat. no power to the element. visual inspection on PCB relay shows the the relay is burnt. put in new board and now “F4” fault shows for both top and bottom ovens. Put in old board and F4 still shows for both ovens.
Trying to avoid having to remove the oven. No wiring diagram. It appears that the oven sensor (upper oven) was replaced some time ago (because of the wire nuts). What is throwing me is that the bottom was working and the only thing that changed was the board and when I returned it to its original state – the bottom is not working.

Any help is greatly appreciated.

I have need of the part number for the small fuse link that is on the back wire to the control. It has Two fairly large spade terminals at either end. I cannot see it listed on the schematic. Can anyone assist?

I think I just need two of these burner knobs. Do you guys know the availability and pricing on them?