0 votes
2k views

My air conditioner is not getting cold enough.

0 votes
2k views

My LG air conditioner is not cooling properly.

0 votes
2k views

My LG air conditioner will not turn on.

0 votes
2k views

I cannot seem to get my window air conditioner mounted properly.

0 votes
2k views

My Window air conditioner just blows out warm air.

0 votes
2k views

My window air conditioner is making odd noises.

0 votes
2k views

My air conditioner starts up and then stops after a few minutes.

0 votes
2k views

The selector switch on my window air conditioner is not working properly.

0 votes
2k views

My window air conditioner smells like chemicals.

0 votes
2k views

My LG air conditioner will not start up.

0 votes
2k views

My LG air conditioner vibrates a lot.

0 votes
3k views

My window air conditioner is not cooling properly.

0 votes
2k views

My window air conditioner is not blowing out any air.

0 votes
2k views

My window air conditioner blows out warm air.

0 votes
2k views

My air conditioner needs to run all the time to keep the proper temperature.

0 votes
3k views

My air conditioner is leaking water.

0 votes
2k views

My air conditioner smells like refrigerant.

0 votes
2k views

My air conditioner is not cooling good enough.

0 votes
3k views

My air conditioner does not start when its turned on.

0 votes
2k views

My window air conditioner is louder than it should be.

0 votes
2k views

My window air conditioner is dripping cold water from the front.

0 votes
3k views

The knob on my air conditioner is not working properly.

0 votes
2k views

My window air conditioner just blows out warm air.

0 votes
3k views
CL

the unit remain on CL
i cant not change any settings.
i tiered to rest it by the braker it did nit help
i took out all the wires to the board and it did not help.
i did change the board a few weeks before that it worked fine.
now its like its frozen nothing works all i get is a consistent CL

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

Hello Technicians, this side by side refrigerator will not dispense ice or crushed ice however it does dispense water. The customer has replaced the auger motor which did not repair the dispenser problem. My thoughts are that the control board might be the problem. Before I replace anything do you have a service manual or a tech sheet or a schematic or any service bulletins on this model . Your help would be greatly appreciated. Also any tips or advise on this issue would be appreciated as well. thank you in advance for your expertise and advise.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

I watched this video on your site: https://www.appliancevideo.com/premiumotr/viking-stove-bake-element-oven-not-heating/

When i pulled the white wire and red wire spade connectors off i put a test to them and had 125 volts;
I hooked them back up to Bake element it was hard to get accurate reading on volt meter. It was kind of reading 20 volts? Would this mean my Bake element is bad ?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

How can I correct this issue ?

0 votes
2k views

Unit drains fine starts to spin but never reaches high speed

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
2k views

does not dispense water
does not dispense ice

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

Hi. My name is Joe. I am trying to trouble shoot a problem with my above mentioned refrigerator. I touched the water dispenser button to switch it from ice and the blue leds went black. I then tried all the other buttons and no matter what buttons I depress the small display lights up with blue diagonal lines across it. I believe at that time the refrigerator was still operating because I left it for 24 hrs before I started to try to diagnose the issue the first thing I did was to power down the unit for a few minutes the powered it back up. When that didn’t work I left the unit again for about 12 hrs and then we noticed that it was no longer cooling or freezing. I checked the interface board for power and I have 12vdc on two different sets of wires. I just want to confirmation that this interface board is my issue because it’s not returnable

  • Guest asked 8 years ago
  • last active 8 years ago
Showing 4471 - 4500 of 9k results