0 votes
26 views

Right door is not closing all the way and keeps popping out. Any videos to fix this issue. Tried hinges, gasket and stoppers nothing working.

  • GeekJames asked 6 days ago
  • last active 5 days ago
0 votes
63 views

This is a double wall oven with the 2 appliance managers. According to the tech sheet, if error code F1E0 appears then the UI must be replaced. I replaced the UI and the error code is still present. The tech sheet also mentions to check 14 VDC from the appliance manager to the UI at connection J4-4 to J4-2. I am getting 14 VDC. I am not sure why the appliance manager is sending 14 vdc to the UI but also sending the error code. I have tried clearing the error codes and discharging the relays on the appliance manager. No fix.

  • ragarcia asked 1 week ago
  • last active 1 week ago
0 votes
76 views

The dryer is not heating. We checked the element, the fuses and everything checks ok. We checked the airflow, unhooked the duct and ran it. Checked out ok. The motor is spinning. What parts should we replace in this dryer sequentially to repair unit?

0 votes
84 views

After beginning a cycle, the initial fill seems to take longer than normal. After a few moments, the unit begins to drain (without beginning to wash) and the “Smart Auto” light blinks.
I have cycled power to reset.
I have also already replaced the thermistor.
There is no water in the drip tray beneath the unit.

0 votes
84 views

The original complaint was that this Dishwasher was not responding to anything. NO POWER whatsoever. So we replaced the main control board and now the dishwasher will turn on but it the display keeps Flashing and not responding to anything. We have reset this board multiple times but it doesn’t seem to help. Does this unit need to have the control board be programmed or could this board be faulty?

0 votes
79 views

Samsung washer. First it wouldnt go into spin. I clean pump filter and now washer does not react. No water, wont agitate or spin. No code displayed
Please provide tech sheet and service manual

  • Raideldz asked 4 weeks ago
  • last active 4 weeks ago
0 votes
69 views

Ge washer GTW330ask4ww. water inlet valve turns on and off intermittently then stops all together. Tank only fills up less than a gallon. Checked for error codes and I get code 5. XML version non-critical.

  • Raideldz asked 4 weeks ago
  • last active 4 weeks ago
1 vote
123 views

Samsung refrigerator model code RF22N9781SG/AA Ice maker is frozen. I cannot get the ice container removed.
How can the ice maker be defrosted without having to disconnect the refrigerator for 24 hours .
please send service manual

  • Raideldz asked 1 month ago
  • last active 1 month ago
0 votes
111 views

This washer machine does not power on any more. I would like to know what parts besides the PCB main board would help solve this problem. Please provide part numbers and diagram of the washer. Does this washer have a noise filter that can solve this problem. Any advice would be help full. They only thing tried was changing the power cord which worked for a few washes before no longer powering on. This is a Samsung washer.

  • GeekJames asked 1 month ago
  • last active 1 month ago
1 vote
125 views

Hi,
I am trying to determine what part I need to fix my dryer EFME627UTT1. Essentially, the dryer won’t start. However, it is exhibiting other strange behavior. The dryer has been in service for about two years since, 9/2019.

When I try to start the dryer, it makes three beeping noises, as it would if the door was open. The door is of course closed however. I put the dryer in diagnostic mode and it displayed an error code of ‘EHd’, flashing as ‘E’ then ‘Hd’. I do not see that code listed in the Dryer Tech Data Sheet. The dryer has a wheel to rotate through the different dry cycles. The center of a wheel has LED lights on it, indicating the time left to complete the dry cycle in minutes. When I rotate through the different dry cycles, the timer doesn’t change as it normally would. It gets stuck on particular value, once at 45 minutes, once at 55, etc. Additionally, sometimes the previous mentioned LED light doesn’t come at all when I start the dryer. However, if I put the dryer in diagnostic mode, the light will then come on and display the error code ‘EHd’ as mentioned previously.

I have taken the dryer apart to check for lint buildup, I found some, but nothing extraordinary. I am assuming its some sort of electronic problem. From some googling it seems it might be the control board, but at around $150 I’d prefer not to miss the call on the diagnoses. Thanks for the help.

  • scarney27 asked 2 months ago
  • last active 2 months ago
0 votes
96 views

Costumer explained Dryer door opens during operation. I ran the dryer and the door never opened.

  • Raideldz asked 2 months ago
  • last active 2 months ago
0 votes
89 views

Already checked and tested power, fuses, magnetron, capacitor and wiring harness for damage.

  • kivery90 asked 2 months ago
  • last active 2 months ago
0 votes
117 views

The washer turns on and goes through the washing cycle. It drains the watet after rinse. But fails to go into spin mode.

  • Raideldz asked 2 months ago
  • last active 2 months ago
0 votes
102 views

When you press bake to preheat upper oven broil element stays on.
When you press bake to preheat lower oven Broil element does not come on only bake element

I need service manuel to change out relay board

  • Loinest76 asked 2 months ago
  • last active 2 months ago
0 votes
138 views

the refrigerator side stays at the set temperature, but the freezer side doesn’t go lower then 41 degrees I have the setting at 5 degrees.

  • flukedup asked 2 months ago
  • last active 2 months ago
0 votes
106 views

This is a coin operated electric dryer. When it is started, the minutes display shows 45 and the light on the top panel is on for “cooling down” instead of “drying”. The heat cycles on and off and the time display counts down normally to 1 minute and remains at 1 minute, and the dryer continues to run and heat and doesn’t shut off. I’m suspecting the timer is the issue. Any assistance would be appreciated.
Thank you.

  • user asked 2 months ago
  • last active 2 months ago
0 votes
114 views

the programming starts normally, water and washing works, when it is on the programming to drain the water the pump does not turn off and shows error I30, I have already replaced the board and the same defect continues

0 votes
117 views
1 vote
127 views

Hi, the washer im dealing with only goes into drain mode when on any wash option selected and started. pressure switch sounds fine clicking when i blow into it. I’ve tried reseting by lifting the lid 6 times. motor led is a steady 1 flash per second. I did replace the board with an amazon purchased board and it was the same result. Any suggestions GE Hydrowave

  • rwerby asked 2 months ago
  • last active 2 months ago
1 vote
161 views

To whom it may concern,
I have a Whirlpool WRF757SDEM refrigerator that has cooling issues in the refrigerator section of the unit;not the freezer . The bottom fresh drawer is ~ 33 degrees, the 3 drawers above that are ~ 40 degrees and the upper main is ~ 47 degrees.These temperatures have been verified by placing thermometers in each section. Due to this elevated temperature we also have had to shut the iced maker off as the ice would melt in the door compartment causing water to run out the chute. I have had a large amount of ice forming behind the bottom drawer ( the one at ~ 33 degrees) and have had to remove this 3 times as it build up there and has caused issues shutting that drawer. The ice was in all the vents located there and I had to take care so it would not get damaged. The freezer portion of this unit works fine and freezes ice in ~ 30 minutes.
I am hoping there is a repair for this erratic cooling as the unit is barely 6 years old and is just out of warranty.
Any and all assistance would be greatly appreciated.

  • toot033 asked 2 months ago
  • last active 2 months ago
0 votes
185 views

Machine not powering on

  • elisheva asked 3 months ago
  • last active 3 months ago
0 votes
165 views

I Keep getting smart auto and heavy lights blinking after the dishwasher is running maybe five minutes, It seems like when it starts it automatically drains. I’ve reset the dishwasher multiple times each time it allows the psycho to go a little bit further but it doesn’t look like it’s putting much water in the dishwasher.

  • Ryan6585 asked 3 months ago
  • last active 3 months ago
0 votes
173 views

Last week I noticed the clock starting losing time. Then both timers stopped counting down when set. Now the interior lights don’t go on when the door is opened. So far, burners and oven work fine.

  • cjhoward asked 3 months ago
  • last active 3 months ago
0 votes
222 views

If you open the following link, that is the noise being made during agitation: https://www.youtube.com/watch?v=WvDDGzhkHu0 . I have removed the Rotor motor and found that at some point, a small amount of water made it’s way to the Rotor Motor as I could see water streaks formed as the motor spun, at speed. Never saw any water on the floor beneath the Washing Machine. I had the Agitator removed at the same time, and found no substantial movement in the shaft at top or bottom. No wear to the splines in the agitator/Impeller or Impeller Insert. The teeth on the Mode Shifter showed some very minor wear. No visible damage to either the Stator or Rotor Motor. Is there a most likely failed part causing the noise or a way to test to find the failed or failing part. My research so far has suggested any of the above mentioned parts as well as the DSM Module. FYI: in searching parts, the Bearing Assy shows as not available. I had GE Parts do some research and the new part # is WH38x24734..Please advise.

  • perplexed asked 3 months ago
  • last active 3 months ago
0 votes
187 views

After disconnecting the dryer to clean the duct, I removed the front to clean the inside and cleaned the duct. Closed up unit plugged in the unit, flipped on the breaker, and powered up the unit. The dryer is powered up but will not go past the selection/timer. The start/pause is not engaging the cycle.I read in some past posts that it could be a belt or a fuse. What are my next steps?

  • The1Jeff asked 3 months ago
  • last active 3 months ago
0 votes
180 views
  • moses asked 4 months ago
  • last active 4 months ago
1 vote
227 views

washer keeps repeating spin cycle
sample no load; put in spin only cycle, starts at 10 minutes, goes yo 8 minutes pauses chimes, goes back to 10 minutes. repeats for hours. during spin cycle washer spins, at mid speed shakes a little bit continues to faster, shakes smooth out spin fast okay. (heard this is normal).

  • joeski1369 asked 4 months ago
  • last active 4 months ago
0 votes
220 views

We smelled burning rubber the last few times we used our washer. Now the agitator spins wildly (out of control) while the drum starts to move, but then both shut down. It seems the machine is trying to start the drain/spin cycle, but can’t. It attempts to start the cycle, but the sequence described above repeats and the machine eventually shuts down. Having repaired this machine a few times in the past, I inspected the belt, which shows no visible signs of damage. With the belt attached, I turned the splutch wheel and I noticed what I would describe as a slip inside the motor.

Please help me figure out what I need to fix this.
Thank you in advance for your help!

-B.J.

0 votes
203 views

This washer is brand new i have looked at the info it came with is says if 888 flashed its the flow meter or the harness and i have replaced the flow meter still the same result

  • dernovish1 asked 4 months ago
  • last active 4 months ago
0 votes
161 views

Need a service manual & wiring diagram along with error codes .
Thanks

Showing 1 - 30 of 8k results