My Maytag dishwasher is unresponsive and will not start.
- Harley Clark asked 9 years ago
- last active 9 years ago
I think I’ve got this narrowed down to needing a main control board and the turbidity sensor, but can’t find the part information. Anyone available to take a look?
- Don Kopecky asked 9 years ago
- last active 9 years ago
This unit is leaking and we have narrowed it down to a blower case assembly but can’t find the correct part information to replace, was hoping to get some help. Thanks.
- T&G Appliance Repair asked 9 years ago
- last active 9 years ago
- Guest asked 10 years ago
- last active 10 years ago
HELP!
We are unable to take off the drain lid and the water wont drain from the dishwasher.
We cant find any videos on your site or ytube to help us.
Can you assist, my mom is frustrated!
Thanks, a son
We have a whirlpool dishwasher
- mama bell asked 9 years ago
- last active 9 years ago
Looking at it now and there’s no tech sheet. Thanks.
- Patrick's Appliance Service asked 9 years ago
- last active 9 years ago
Dishwasher will not start. Left hand panel cycle lights on touchpad when pushed work (pots pans, normal, etc.) and stay on for a bit then turn off. Right hand cycle lights (hi temp, sanitize, heated dry) do not come on. Have tested continuity of fuse – all OK. Have tried reset of control board using hi temp and dry buttons being pushed a total of 10 times alternating buttons – but since the lights do not come on it’s not working. Is there a way to test the control board? Is the touchpad part of the control board unit or is it a seperate part? Anyway to test that? Thanks for any assistance.
- Dan asked 10 years ago
- last active 10 years ago
My Jenn-Air dishwasher is not draining properly
- Patrick's Appliance Service asked 7 years ago
- last active 7 years ago
Dishwasher was flashing on smart auto normal. I tried to clear by turning power off for approximately 5 minutes still had same problem. I replaced main control board unit ran Ok while I was there testing it . Customer called back and said unit is doing the same thing.
- Gary Williams asked 9 years ago
- last active 9 years ago
I have a dish drawer that overfills.
- Guest asked 8 years ago
- last active 8 years ago
How many times do you have to push the buttons in the right time
- Guest asked 9 years ago
- last active 9 years ago
My Frigidaire Professional FPHD2491KF buttons don’t work. Well only two light up when I press them. The start button does not work so I can’t run the machine. Would that be a console assembly problem or a pc board problem? How would I find out which one needs to be replaced as I have searched many forums and websites indicating that it can be either the PC board or the Consol assembly (panel where you press buttons) Thanks!
- Pedro asked 9 years ago
- last active 9 years ago
Thought I had this narrowed down to needing a fill sensor, but when I returned to replace it, the unit was still getting errors. Now I’m thinking flow meter but can’t find the part information. Does somebody there have it?
- Fred Abernethy asked 9 years ago
- last active 9 years ago
I have a bosch dishwasher showing an E24 code. What does this mean?
- David Sutton asked 6 years ago
- last active 6 years ago
Samsung dishwasher that is giving a 7E code. Can you tell me what this is and how to fix it, and hopefully a video of the repair
- Guest asked 8 years ago
- last active 8 years ago
A U1 deals with the fill fault. It talks about the water valve needing replacement. It doesn’t always stop in the fill cycle. Could it possibly be a electrical switch and how do I check the possible problems. Also could I replace parts myself?
- Steve moore asked 10 years ago
- last active 10 years ago
My customer called about her kitchen sink being clogged. And when the dishwasher drained it just added to the drainage problem.
- Guest asked 8 years ago
- last active 8 years ago
Our dishwasher lights up, has power, but will not start. Sometimes if I cancel it, open and close the door, and hit start again, it begins. But it’s getting more and more frustrating. Any thoughts on what it could be?
- Amelia A. asked 10 years ago
- last active 10 years ago
Customer gave no details of when the dishwasher gives the code, only that it reads the code: nE.
- dwoods asked 4 years ago
- last active 4 years ago
No error codes or flashing lights. water seems to get hot.
- Guest asked 8 years ago
- last active 8 years ago
- Guest asked 9 years ago
- last active 9 years ago
Customer complains that his dishwasher Silverware rack dosnt dry at all, but the rest is dry???
- Guest asked 7 years ago
- last active 7 years ago
I got it apart and found a level sensor that I think is bad, but doing the lookup I am having a hard time finding the correct part number. It’s the water sensor if that helps. Not with the unit to give you the model #.
- Don Kopecky asked 9 years ago
- last active 9 years ago
I haven’t had a chance to physically diagnose this but want to take something with me since the customers requested the work be done asap for the holiday. I think it’s the console assembly but wanted to verify with you guys.
- Don Kopecky asked 9 years ago
- last active 9 years ago
Please include manuals listed below if you have them.
DDT575S
GDT580S
GDT720S
CD725SSF
GDT740SIF
PDT750SSF
- Gary Williams asked 6 years ago
- last active 6 years ago
Not heating, blinking complete cycle not staying solid
- Guest asked 9 years ago
- last active 9 years ago
We have a Whirlpool dishwasher, above model, runs to about 1/2 way thru cycle and shuts off, cancel drain light blinks continuously. Any help/ advice we can get with this unit would be appreciated.
Thanks in advance
- David Sutton asked 8 years ago
- last active 8 years ago