My Whirlpool dryer is making a loud noise not heating and has a burning smell.
- Curtis Appliance Repair asked 9 years ago
- last active 9 years ago
I replaced the computer because it was working intermittent it’s still doing the same thing
- Guest asked 9 years ago
- last active 9 years ago
Microwave turns on for 2 seconds and then turns off. History: I changed out a blown fuse about six months ago but did not know at the time I should have changed the monitor switch. Last time it was dead and now it just turns on for 2 seconds. Any ideas what I should be looking for? Model #HMB5050/01 FD 9007100017 FCC ID ACLAP7A01
- Curtis Appliance Repair asked 9 years ago
- last active 9 years ago
I got this apart and diagnosed it needing multiple parts. Could you send over purchase information on them so I can get a quote written up? Thanks.
Primary, secondary, and monitor switches, as well as the fuse.
- James Buchanan asked 9 years ago
- last active 9 years ago
ciruct barker is good but im not getting any power to the unit
- Guest asked 8 years ago
- last active 8 years ago
there is power going to the board but nothing happens it is a Kenmore
- Guest asked 7 years ago
- last active 7 years ago
The board on this unit was flicking off and on and constantly beeping. Will do this while the unit is idle. I changed the control, everything seemed ok, get a call and now the board says needs service and is beeping. Any ideas?
- Guest asked 8 years ago
- last active 8 years ago
How do i change the light bulb in my microwave.
- Harley Clark asked 6 years ago
- last active 5 years ago
microwave worked fine warming the chicken….went to go reheat some vegetables and nothing..heard some popping sound like a fuse but the fan works and lights work and turntable spins
- leroy needham asked 10 years ago
- last active 10 years ago
PANEL TURNS ON BY ITSELF AND CHANGES SETTINGS, THE MICROWAVE ITSELF DOESN’T TURN ON, BUT THE PANEL JUST DOES RANDOM THINGS. ANY IDEAS?
- Guest asked 6 years ago
- last active 6 years ago
My GE microwave is unresponsive and shows nothing on the display panel.
- Patrick's Appliance Service asked 9 years ago
- last active 9 years ago
GE microwave that just shuts off after about 10-15 seconds and then resets to where you have to set the date and time. I am thing PCB, any suggestions?
- Guest asked 8 years ago
- last active 8 years ago
The turntable on my Kenmore microwave will not move.
- Fred Abernethy asked 8 years ago
- last active 8 years ago
I am getting power to the outlet but nothing to the microwave
- Guest asked 8 years ago
- last active 8 years ago
Error code 1006 on Thermador
- Guest asked 5 years ago
- last active 5 years ago
This is an oven/microwave combo. Oven works fine and microwave works good except for it will not run longer than 1 minute. At that point, in the oven control board screen it will give an error code of F3E2. The microwave board doesn’t display this code. The oven sensors check fine as well as the oven works great! Not sure what this could be causing this as all works well except for the 1 minute time issue. Set for 3 minutes will cut off completely at 2 minutes. Any time frame will do the same.you can also start the microwave back up instantly and it will run for 1 minute. Any help would be great!!!
- Guest asked 5 years ago
- last active 5 years ago
So I had a noise filter burn up. Checked the magnetron and it’s bad. So replaced mag, cap and diode and as soon as youug it units trips the breaker. I’ve check all the wires and all the components and I can find what’s grounding causing the breaker to trip. Any ideas?
- Guest asked 9 years ago
- last active 9 years ago
My door wont latch shut on my Samsung microwave.
- Don Kopecky asked 9 years ago
- last active 9 years ago
Unit dead, no display.
Found vent thermostat (diagram part 115) scorched with riveted terminals sloppy loose. Connecting wire and stake on terminal cooked.
Jumpered terminals and microwave worked fine.
Ordered part three times but it keeps arriving N.O. Instead of N.C.
What could I be missing or where can I get the proper N.C. Thermostat (150degrees) I believe?
- Guest asked 8 years ago
- last active 8 years ago
Had a power surge during a storm and since then the microwave will not do anything.
- Harley Clark asked 6 years ago
- last active 6 years ago
My whirlpool microwave is making too much noise.
- T&G Appliance Repair asked 7 years ago
- last active 7 years ago
Kitchen Aid KEMS308 Built in Combo. Microwave wont heat but seemingly works otherwise. Got F1E5 Replace Micro Inverter Error.
- James Buchanan asked 5 years ago
- last active 5 years ago
I found the primary interlock switch faulty on arrival, replaced and still had the same issue. The fan that comes on when the magnetron is active is only turning on when you open the door. I confirmed all the micro switches were functional at this point. My experience in the past is that one of the switches would cause this. I am suspectin that I am missing something here.
- Guest asked 7 years ago
- last active 7 years ago
KITCHENAID MICROWAVE RAN DIAGNOSTICS ERROR F1 E5 SCREEN SAYS REPLACE MICROWAVE INVERTER. I REPLACED INVERTER AND MICROWAVE CONTINUES TO GIVE SAME ERROR CODE. I CHECKED SOME OTHER POSTS AND THEY INDICATED THAT HE APPLIANCE MANAGER IS THE CULPRIT. I REPLACED THE APPLIANCE MANAGER DIAGNOSTICS SAYS STILL SAME ISSUE F1 E5 CAN YOU TELL ME WHERE TO GO FROM HERE. I TRIED TO RESET ERROR BY GOING INTO DIAGNOSTICS OFF OFF START THEN 6 THEN 6 AGAIN THEN PUSH START AND THAT IS SUPPOSED TO RESET BUT ONLY BEEPS.
WHAT OTHER CHECKS CAN I DO.
- Guest asked 5 years ago
- last active 5 years ago
- Guest asked 6 years ago
- last active 6 years ago
I cannot get the controls to respond on my microwave.
- Patrick's Appliance Service asked 6 years ago
- last active 6 years ago
My GE microwave will not shut off.
- Patrick's Appliance Service asked 8 years ago
- last active 8 years ago