Appliance Type: Stove / Oven / Cooktop

115 volt one leg of bake element, other leg 70 volts not enough current/volts to power element

Have a unit with no display when powered up. Display will come on when microwave door is opened and clock can then be set. Lower Oven can then be programmed and will start to heat as long as microwave door is opened. Lights also get very bright while oven is heating (oven and microwave lights both come on when either door is opened).If microwave door is closed relays can be heard clicking then display and oven both turn off. If microwave door is opened then clock display comes back up; although if you wait awhile before opening the door it just reverts to power failure mode. Relay board was already replaced to no effect.

Oven. Would not bake. Replaced e.o.c. Now the oven will come on but the bake element only gets 110 to it so it will only get warm. If you put it into broil the broil element works. When I put it into bake no voltage come out of relay with the yellow wire coming out of it that goes down to the bake element. Checked wires from control to bake element they check out ok. Any help would sure be appreciated. Thanks

The door lock is no longer available. Is there a way to bypass the door lock?

Evan if i put to 250 only the broil heating element goes on

I have a 48″ Jenn-air range ; that main oven flame was sputtering and shut off. I started smelling gas and called gas company they came out and said he had a gas leak. I went out and order a regulator. Replaced regulator unit still does the same thing all other burners are Ok could it be the safety valve?

There is a fuse link in behind the control board on this model that is blown. It resembles a diode a little. I cant find this part on any drawing and was wondering if you could help me with the part number to this fuse?

One of the surface burners on my Kitchenaid stove is not getting hot.

Good morning. I did not look at this stove yet, but could some one
walk me through the diagnostic steps? Thanks, Todd from ny

Do you have a video on how you replace the bake element on this double oven. I also like to know if you have a diagnosis sheet or cheat sheet that I can put the unit into diagnostic mode? I don’t have anything on this oven except a schematic. Takes a long time to get to preset temperature 30 min.

Burners now come on sporadically but are mostly out.

The door is not locked however I’m still getting this message.
It happened once before we unplugged it and it worked fine now however we unplug it we get the power failure message and then F5 E7

The door on my Whirlpool range will not close properly.

No display, No bake, No broil.

The broil and bake igniters are not turning on.
The oven chimes when I switch it to bake or broil but the igniters do not glow hot. Could the main circuit board go out? This is a very popular oven and brand. I could not find it on your website. When will you have a video on this range?

Kitchen Aid oven.takes long time to heat up,and won’t reach temp set to.

My cooktop smells like its burning.

This unit has a hidden bake element. I’m wondering how to remove it. It doesn’t have any screws on the inside to remove the bottom panel to get to it.

Could this be a mainboard issue?
Bake relay P7 Yellow and P2 Black 120 ac when the oven is off and 0 ac when it is on.
Broil element K2 relay also 120 ac when the oven is off.

My name is Roland,
Question: I am working on a Kitchen Aid dual fuel gas range MD# KDRU7893VSS03 SN:DB1375935. The issue with this unit is there’s an error code which says NTC out of Range. I have tested all fuses in the back of this unit, I have changed the sensor -W1076760, the boiler assy -9758598, the appliance manager-w10339702. Still when power up, it goes into lock out with NTC out of range, call for service.
Can anyone help with this issue please. I await your response.
Roland

Hello,

When you open bottom oven door the display says bad line then the clock appears then the display goes blank…

Customer said one time no burners would come on when set. Now the right front won’t boil water. Could this be a bad appliance manager board? Both duel elements work. Even on number 10 setting it will go off with a pan of water on it. Any advice welcome.