0 votes
2k views

Why Do I Have Suds Left Over in My Washer?

0 votes
2k views

Heater tested bad no continuity or resistance replaced but error won’t go away comes up after the cycle. How can I clear the error code?

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views
  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

We need a tech sheet and service manual

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

Need a service manual on this smart all-in-one washer & dryer combination unit.

0 votes
2k views

I put new belts on my washer. it was tilted back so when i turned it on it went to wobbling and then cut off. since then i put it back down on the floor to let the water level out and it will not start.

1 vote
6k views

Maytag top load. Wont power up. Has F6 E2 code. Communication error between UI and ACU. Has 120v to Main board. Light on main board is flashing signifying 5VDC present. Tech sheet says preform key activation and encoder test (passed) and check for voltage to main board. All good. I m thinking UI is bad. What do you think?

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

Drains, fills,door locks, but timer keeps resetting ( adding more time to the cycles) when there is like around 9 mins left in cycle. Clothes are still wet. But it spins. Can’t get it to diagnostic mode to read any error

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

The led on the motor is not working so I can’t read the error code. The washer will only fill and drain. It will not agitate or spin.In The test cycle also it only fills and drain s. I need a service manual and any videos.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

My Kenmore washer is displaying an e24 error code.

0 votes
2k views

Originally, the washer had an LE code. I tightened the bolt in rear that holds rotor in place (4040FR4051C). After that the washer would agitate clockwise and spin just fine, but everytime it tried to agitate counter clockwise it would lock up, the magnets where so strong I coulndn’t even help it turn with my hands. So at this point, I proceeded to change rotor, then stator, with the same result. All the wires looked good except for one ground wire that I repaired. Any Ideas or suggestions?
P.S.—-What is the easiest way to get broke bolt out of tub shaft (4040FR4051C), as I have now successfully broken the bolt off from taking on and off so much I guess.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views
  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
10k views

E01 and F01 coming up on Maytag Maxima front load washer

0 votes
50k views

I have a code F03 and E01 showing.

0 votes
3k views

I have a Maytag neptune washer and get the nd error even after I replaced the water pump, the water inlet and the water pressure sensor. The pump is working I can hear it drains the water out but not all of it.

0 votes
2k views

Washer: The power is on but it stopped mid cycle and will not resume. I unplugged and repligged it. Power and lights come on the machine but when I push start button I just hear severlal needs but doesn’t start. It already has water in the tub and just stopped.

0 votes
26k views

E01 and F01 coming up on Maytag Maxima front load washer.

0 votes
3k views

looking for f6 e02 fault code whirlpool washer WFW94HEXW2 any help appreciated

1 vote
3k views

The washer fills then stops. If you restart it again, it squirts a little water then stops. No agitate or spin.

The lid switch is defective and I’ve ordered a replacement.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

Washer was taking long periods of time to sense the clothes in the tub, could restart and sometimes would work right sometimes wouldn’t. It will work correctly with no clothes in washer, but not with clothes in tub. Now it won’t operate at all. Any suggestions?

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

I have a GE washer with a customer complaint excessive lint being left on clothing. The model number is worn off so I cannot provide that. It is a top loader high efficiency, stainless steel tub. It is a unit with the inverter board motor. I took the inner tub out and cleaned the outer and inner tub to almost new condition so the lint has to be coming from clothing being washed. What causes this? It is evident on the clothing before it goes in the dryer and does not come off in the dryer. Thank you for any tips.

0 votes
3k views

F-11 error code.

0 votes
3k views

I am looking for main pcb board lg model WM2277HW/01 board 6871ER1078T.

0 votes
2k views

Washer going off balance every other cycle rods have plastic ball and sockets
Tub ring has liquid inside.
Help if you have ideas
Change rods?

1 vote
3k views

Washer fills then stops.
I manually turn timer 1 notch for the machine to proceed, it then turns and stops
Machine won’t start cycle or agitate.
I turn timer to Spin cycle, It will only drain and won’t spin.

  • Guest asked 7 years ago
  • last active 7 years ago
1 vote
5k views

I need service manual for this washer. Or specifically if you can provide a video or repair instruction on how to replace washer drive shaft part number WH38X24734 that will be great. Very loud and wobbling and moving all over the place when spinning. Thank you.

1 vote
3k views

The washer just stops at 17 minutes left on all selections except bulky items. It will run the entire load on bulky items. There are no stored error codes and the unit completes the automatic diagnostic mode with no problems.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

I am looking for main pcb board lg model WM2277HW/01 board 6871ER1078T.

0 votes
2k views

My Whirlpool washer is displaying an off balance error code.

0 votes
3k views

I need a service manual. Is there a way to manually test this washer? Is it in the manual?

  • Guest asked 7 years ago
  • last active 7 years ago
Showing 421 - 450 of 2k results