Filter
Sort by: Newest First
Ask a Question
0 votes
1 answer
2k views
soap left over after every wash
Washer Whirlpool

Why Do I Have Suds Left Over in My Washer?

0 votes
1 answer
2k views
Replaced washer heater error won't go away
Washer LG

Heater tested bad no continuity or resistance replaced but error won’t go away comes up after the cycle. How can I clear the error code?

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
1 answer
2k views
control lock light is on cant start the washer
Washer
  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
1 answer
2k views
when start button is pushed the washer will not start and after about 30 seconds it flashes e1-f6
Washer Maytag

We need a tech sheet and service manual

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
1 answer
2k views
Need service manual
Washer Whirlpool

Need a service manual on this smart all-in-one washer & dryer combination unit.

0 votes
1 answer
2k views
Washer is off balance
Washer Maytag

I put new belts on my washer. it was tilted back so when i turned it on it went to wobbling and then cut off. since then i put it back down on the floor to let the water level out and it will not start.

1 vote
1 answer
6k views
F6 E2 code
Washer Maytag

Maytag top load. Wont power up. Has F6 E2 code. Communication error between UI and ACU. Has 120v to Main board. Light on main board is flashing signifying 5VDC present. Tech sheet says preform key activation and encoder test (passed) and check for voltage to main board. All good. I m thinking UI is bad. What do you think?

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
1 answer
3k views
Spin cycle will not finish and timer keeps resetting when it gets down to the last few minutes.
Washer Samsung

Drains, fills,door locks, but timer keeps resetting ( adding more time to the cycles) when there is like around 9 mins left in cycle. Clothes are still wet. But it spins. Can’t get it to diagnostic mode to read any error

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
1 answer
2k views
Is it the electronic control or the motor?
Washer GE (General Electric)

The led on the motor is not working so I can’t read the error code. The washer will only fill and drain. It will not agitate or spin.In The test cycle also it only fills and drain s. I need a service manual and any videos.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
1 answer
3k views
E24 error code
Washer Kenmore

My Kenmore washer is displaying an e24 error code.

0 votes
1 answer
2k views
NOT TURNING BUT ONE DIRECTION
Washer LG

Originally, the washer had an LE code. I tightened the bolt in rear that holds rotor in place (4040FR4051C). After that the washer would agitate clockwise and spin just fine, but everytime it tried to agitate counter clockwise it would lock up, the magnets where so strong I coulndn’t even help it turn with my hands. So at this point, I proceeded to change rotor, then stator, with the same result. All the wires looked good except for one ground wire that I repaired. Any Ideas or suggestions?
P.S.—-What is the easiest way to get broke bolt out of tub shaft (4040FR4051C), as I have now successfully broken the bolt off from taking on and off so much I guess.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
1 answer
3k views
What's error code E11 related to?
Washer Electrolux
  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
1 answer
10k views
E01 and F01 error codes
Washer Maytag

E01 and F01 coming up on Maytag Maxima front load washer

0 votes
1 answer
50k views
F03 E01 error codes
Washer Whirlpool

I have a code F03 and E01 showing.

0 votes
1 answer
3k views
ND error code
Washer Maytag

I have a Maytag neptune washer and get the nd error even after I replaced the water pump, the water inlet and the water pressure sensor. The pump is working I can hear it drains the water out but not all of it.

0 votes
1 answer
2k views
No power
Washer Maytag

Washer: The power is on but it stopped mid cycle and will not resume. I unplugged and repligged it. Power and lights come on the machine but when I push start button I just hear severlal needs but doesn’t start. It already has water in the tub and just stopped.

0 votes
1 answer
26k views
E01 and F01 coming up on Maytag Maxima front load washer
Washer Maytag

E01 and F01 coming up on Maytag Maxima front load washer.

0 votes
1 answer
3k views
f6 e02 fault code
Washer Whirlpool

looking for f6 e02 fault code whirlpool washer WFW94HEXW2 any help appreciated

1 vote
1 answer
3k views
Removing the cabinet
Washer GE (General Electric)

The washer fills then stops. If you restart it again, it squirts a little water then stops. No agitate or spin.

The lid switch is defective and I’ve ordered a replacement.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
1 answer
3k views
SENSING ISSUE
Washer Whirlpool

Washer was taking long periods of time to sense the clothes in the tub, could restart and sometimes would work right sometimes wouldn’t. It will work correctly with no clothes in washer, but not with clothes in tub. Now it won’t operate at all. Any suggestions?

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
1 answer
3k views
Excessive lint left on clothes
Washer GE (General Electric)

I have a GE washer with a customer complaint excessive lint being left on clothing. The model number is worn off so I cannot provide that. It is a top loader high efficiency, stainless steel tub. It is a unit with the inverter board motor. I took the inner tub out and cleaned the outer and inner tub to almost new condition so the lint has to be coming from clothing being washed. What causes this? It is evident on the clothing before it goes in the dryer and does not come off in the dryer. Thank you for any tips.

0 votes
1 answer
3k views
F-11 error code
Washer Whirlpool

F-11 error code.

0 votes
1 answer
3k views
I am looking for main pcb board lg model WM2277HW/01 board 6871ER1078T
Washer LG

I am looking for main pcb board lg model WM2277HW/01 board 6871ER1078T.

0 votes
1 answer
2k views
Off balance
Washer Whirlpool

Washer going off balance every other cycle rods have plastic ball and sockets
Tub ring has liquid inside.
Help if you have ideas
Change rods?

1 vote
1 answer
3k views
washer fills then stops. Won't start cycle or agitate. spin cycle only drains and won't spin.
Washer Maytag

Washer fills then stops.
I manually turn timer 1 notch for the machine to proceed, it then turns and stops
Machine won’t start cycle or agitate.
I turn timer to Spin cycle, It will only drain and won’t spin.

  • Guest asked 7 years ago
  • last active 7 years ago
1 vote
3 answers
5k views
Loud Spin. Bearing is shot.
Washer

I need service manual for this washer. Or specifically if you can provide a video or repair instruction on how to replace washer drive shaft part number WH38X24734 that will be great. Very loud and wobbling and moving all over the place when spinning. Thank you.

1 vote
1 answer
3k views
Stops with 17 minutes left.
Washer Whirlpool

The washer just stops at 17 minutes left on all selections except bulky items. It will run the entire load on bulky items. There are no stored error codes and the unit completes the automatic diagnostic mode with no problems.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
1 answer
3k views
Need new board
Washer LG

I am looking for main pcb board lg model WM2277HW/01 board 6871ER1078T.

0 votes
1 answer
2k views
Off balance
Washer Whirlpool

My Whirlpool washer is displaying an off balance error code.

0 votes
1 answer
3k views
Won't spin dry
Washer Samsung

I need a service manual. Is there a way to manually test this washer? Is it in the manual?

  • Guest asked 7 years ago
  • last active 7 years ago
Showing 421 - 450 of 2k results
«1...1314151617...63»