Brand: Whirlpool

I’ve just tried to use my broiler for the first time, even though I’ve had this oven for awhile already, and it doesn’t work correctly. It seemed to preheat, but then when I put my fish in, and set the timer, it seems to have shut off on it’s own. I started it over, did the same thing. Is cooling down and not staying on even though it says it is.

i have noticed that the washer is making the washing sound but when i peep in the lid i could see that the tub is still stationery, after it reaches the spin cycle it just stops and the lid lock keeps blinking.i had to cancel the cycle and the i enter diagnostic mode and it shows F7 E1. can u help?

after changing the shifter on my washer, the washer was not starting and eventually it did. then it began to wash and it stopped at the spin cycle and the lid lock kept flashing . i cancel the then did a test and found that the basket has a sensor fault, what do i do now?

after seeing what the technician did when he came to asses the fault on my washer i went and bought the part and installed it and tried to do the same but was unsuccessful in the programming part. i saw that he spin the drum of the washer slowly for a while but now i am doing it but dont know why. i am trying to save money here but it seems i would have to spend money for him to come and do the same thing. please help

Motor spins, apparently pumps water, hear clicking noise that matches RPM of motor. No tub spin or agitation. How do I gain access to look at inside — doesn’t top assembly lift up, and if so how?

a technician came and check my washer did a diagnostic test and found that the shifter actuator is faulty F7 E5. he places one of his and it showed that is is working but he did a few more test and he spin the drum of the washer and program it back. i recently bought the same part and change it myself and i would like to know how to program it so that it can resume normal washing; urgently need your help here

Dw seems to be stuck in wash mode, Couldn’t make heads or tails of diagnostic mode. In light wash I got the dispenser to open but never heard a drain cycle after the prewash, I may have just missed it as I was going over tech sheet in library. Unit seems to pause for a few seconds and then go back in to wash mode. pushed canel drain 45 min in.lw cycle should last a total of 25 min max according to tech sheet. HO states wash times exceeding 4 hrs, that will only stop if terminated. the unit appears to have a pressure switch for soil sensing,wondering if this could cause this problem. Any thoughts folks?

This is actually a series made by Whirlpool 810-811. The motor is not running and water doesn’t drain. However, the board will still go thru its cycles as if it is working properly. Is there a reset button somewhere on this unit to start the motor? This is a 12 year unit which I’ve probably used half a dozen times.

What recommendations can you provide as I’m a DIY’er?

Does anyone know of a parts store that does not have a core charge on boards? Please share…Thanks

Having a problem removing the icemaker on thid box. model GI6FDRXXY03
Wire harness cover comes off and latch holding icemaker in moved easily but the icemaker will not move.

Anyone have a manual on this frig.

There is a sturdy piece of plastic where i though the grommet should be and i am afraid to pull it out because i might break it.

Complaint: Unit taking very long time to complete cycle and or pauses with water,
but will complete cycle. This unit is located in a Seminary with multiple users so can’t get proper feedback. Any help appreciated.

We have a very strange problem with this washer, Whirlpool ,mod.WFW8400TW00
It leaks in the clean cycle only . Couldn’t find the source of the leak
because dryer is on the top of the washing machine ,located in the very small room .
Anyone knows about the source of the leak in the clean cycle so we can save our time
without going back and forth ?
Thank you

We need some advice on a Whirlpool washer WTW4910XQ0.
When the unit is running the belt keeps sliding down and coming off.
Any advice would be appreciated.

Power O.K. to terminal block. No Lights, Nothing Works.
Replaced main control board per troubleshooting guide supplied with dryer, but did not fix problem. Dryer will operate fine once (infrequently) then nothng works after that. Checked through to control panel connections..everything is clean and tight, Dryer would not work after replacing main control board. Put old board back in and it worked for one complete cycle. Then no lights and no start situation again.

Door switch clicks crisply and seems O.K. but haven’t tested due to access.. Light comes on inside drum when door open and off when door closed.. If I need to remove back panel I need help with how to remove “clip” at vent opening….can’t figure how to unclip.

There are two boards inside user panel….nothing burnt, all looks clean and fine except a tiny bit of corrosion on the board side of the wide ribbon cable. (cleaned and WD-40).

If I remember correctly, both times that the user panel lights came on and dryer worked was directly after I had thrown the main fuse (at the main house fuse box) off and then on, but I have been unable to duplicate this scenario.

Please help, and if I have to remove back panel from dryer cabinet, advise how to unclip the clip at the vent opening.

Thanks

Not sure if the dispenser is broken or if it needs cleaned out but I’m not very knowledgeable about appliances. Any help would be great.

We have watched and repaired/replaced drain tube. However, we still have ice forming on the floor of the freezer and are wondering if we need to defrost the drain line and how to do it.

Our washer has a very slow but steady drip of water inside the tub, even when not being used. I checked the connections, and everything is tightened. What should I do to stop it?

I thought it was odd that our stove tripped a breaker, as soon as I reset it, it seemed fine. What should I check on it to ensure it doesn’t keep happening?

washing machine has error code and will not work. Couldn’t find what it means or what we’d need to do to fix it.

Serial # SJ3751348, built in Sept 1999. I cleaned a ton of dust off the coils first. Still won’t get cold. The fan motor is working and airflow is coming into the fridge and freezer. I hear a clicking noise coming from the plug on the side of the big black pot with copper tubes coming into it. Every 3-4 minutes I hear an initial “click”, then nothing happens for about 1 minute or so, then another “click”. Sounds like a relay opening and closing, but nothing else happens.

do you think the 25 amp fuse would be the most likely of the problem?

Burner comes on for 10 seconds and cuts off. Clothes never heat up enough to dry.

My washer fill but doesn’t start to wash or agitate after it fill. It change the light from fill to wash but stay that way and do nothing. If I put it on spin and drain it works great, so I believed that the motor is ok. When the machine is performing it locks the lid. What could this be, and how can i fix it? Thank for the You Tube help!

I keep finding them and don’t want them to get stuck in the pump. Can I clean out the drum somehow?

The water dispenser in the door gives me water for a very brief couple seconds and then just trickles out like it’s not on or something. I seem to still be getting ice made so I have no clue as to why the door won’t give me water. What can I check to figure this out myself?