Appliance Type: Dryer

Push button for start broken out. Go to replace console and find once I remove the 2 circuit boards from the console that the start pad on user interface board is busted. Great, more issues. LOL
Trying to price out part, I run into a headache. Original part number is W10110658.
1. First parts house tells me special order. They check Whirlpool inventory and says they have 10 in stock. But customer doesn’t want to wait.
2. Second parts house says part number changes to W10294715. In stock. Something don’t seem right. Call 2 more parts houses.
3. Third parts house says part number now W10756696. Not in stock.
4. Fourth part house says part number is W10294708. In stock.

Hi folks,

This unit is only about three years old and in a RV. I knew I should have walked but they sounded like nice people and they are a couple of snow birds from Michigan! Nice folks.
Compliant: Press the start button..nothing. checked all the oblivious things but I cannot get voltage to the timer or start button. Checked the fuses, voltages coming in! Small area to work in. Any ideas??

All ideas greatly appreciate!

Thank you,

Jan
Barney’s Appliance
Palm Bay, FL

My Estate brand electric dryer is not heating.

My GE dryer is making a squeaking noise and keeps getting louder.

what should I replace??

Thought it just wasn’t heating up, but it actually wasn’t running at all. Looks like a busted door switch. Do you guys carry it?

My gas Kenmore dryer is not heating.

My Maytag dryer is making a growling noise.

GOOD MORNING. I CHANGED THE COILS, AND THE BURNER WILL NOT LITE. WHEN THE START BUTTON IS PUSHED THERE IS SOME WHAT OF A CLICK AND THEN A VERY LOUD WHINNING-BUZZING SOUND, THEN THE ELEMENT GLOWS, THEN AFTER ABOUT 10 SECONDS A SECOND CLICK, THEN IT SHUTS DOWN. IT WILL REPEAT THIS CYCLE OVER AND OVER. I HAVE CONTINUITY AT THE FLAME SENSOR AND THE IGNITER OHMED OUT AT .5, I BELIEVE, BUT NO CONTINUITY BUZZ. I THEN TOUCHED THE IGNITER SOME WHAT LIGHTLY AND IT BROKE IN TWO VERY EASILY. I HAVE A LOCAL PARTS PLACE THAT WILL TEST THE VALVE IF I TAKE IT TO HIM. I HAVE HEARD OF GAS STOVES NOT IGNITING BECAUSE THE IGNITER IS STARTING TO FAIL AND DOES NOT REACH PROPER TEMP FOR THE GAS TO FLOW, MIGHT THIS BE SIMILAR? THANKS, TODD FROM NY.

I am working on a Kenmore HE3. I have replaced the coils and the ( cycling thermostat ). And the burner continues to run for about 10-12 seconds then shuts off. After a few minutes, the igniter comes on, the gas valve opens up and the burner starts and run for 10 seconds or so, then shuts off, and the cycle continues.
I think it’s the gas valve, but before my customer spends that kind of money. I want a second opinion. What do you think, and why?

Bob
I would appreciate a quick call if possible. 609-437-7436
Robertdennis3382@yahoo.com

THE CUSTOMER IS TELLING ME THAT THERE IS HEAT, BUT THE DRYING IS TAKING TOO LONG. I DID NOT GO TO SEE IT YET, COULD SOMEONE WALK ME THROUGH THE DIAGNOSIS? THANK, TODD FROM NY.

My gas Kenmore dryer is not heating.

My Maytag dryer is making a loud squealing noise.

My Whirlpool dryer is not heating.

Gas dryer igniter will glow for about 8-10 seconds the click and will not light. Could not find anywhere what the resistance should be on the igniter. Any suggestions on what else could cause this?

Ge dryer that will not stay running after you turn the start knob. If you hold the start knob over the dryer will run, but as soon as you let it go, the dryer shuts off. The start switch has been replaced. Does this sound like a motor issue or is it possible that the switch to the pulley is malfunctioning? Any advice would be great. Thanks in advance.

I AM TRYING TO ORDER THE HEATING ELEMENT AND THE DIAGRAM SHOWS I HAVE TO BUY THE ENTIRE HOUSING. THE CUSTOMER WAS SHOCKED AT THE PRICE, SO I CALLED A LOCAL SUPPLY HOUSE AND THEY SAID THAT THEY CAN GET THE RESTRING COIL THAT IS MADE BY FRIDGADARE. DOES THIS SOUND CORRECT AND HOW DO YOU MATCH THE ELEMENT? THANKS, TODD FROM NY.

My Maytag dryer will not heat .

My Amana dryer will not heat.

My GE dryer is not heating and is making a squeaking noise.

I have a Whirlpool dryer It keeps blowing thermal fuse by blower (part 3392519). I replaced thermistor (part 8577274) and thermal fuse about 4 months ago. Checked venting and it was clear, customer had it cleaned out about six months ago. What else could be causing this?

THE DRYER IS NOT HEATING. TUMBLES AND BLOWS COLD. HELP! TODD FROM NY

Wall mount GE dryer:When press start bottom starts but doesn’t continue running.is it the motore?

My whirlpool dryer is not tumbling.

My KitchenAid dryer will not start, any recommendations of where to start ?

Replaced the terminal block and now the dryer will run for 10 seconds or so then shut off. Will restart in roughly 10 min. I am thinking motor, what may be some other suggestions? All power and wires are good.

High pitched Squealing

My gas whirlpool dryer is not heating. What are the most common problems that are the least expensive to repair.

Had a whirlpool dryer , ( LINT FILTER ON TOP ) last week, customer complained very noisy and walks on floor.
Found blower wheel shattered, about 10 pieces up to 2 feet into vent tube.
Order part, ( more expensive wheel) return to home and pull drum to lock shaft tand remove and install new blower.
The motor has a 2nd idler shaft next left of the main shaft and a pulley system between them
which looked like it increased the blower wheel rpm. My guess, over 3000 rpm
They also decreased the lint filter chute port to about 1/2 of original size.
Outlet airflow pressure seemed higher velocity, probably designed for lower volume, higher pressure or something..
Changed the blower and found dryer had originally run long enough to also overheat the
element making it sag and short to frame. This caused temp to rise and kick off the
small thermal fuse ( 3392519 ).
Dryer is much noisier design then the original version and I was wondering if this is
a test version or have they switched designs. Any input is greatly appreciated

I have not ever ran across the control lock light ever doing this. I unplugged the dryer. It goes back to flashing as soon as I plug it back in. I checked on the cost of the user board and it’s one high priced part. Thank you for all your help.