Appliance Type: Dryer

have a dryer samsung code display is either ee fe or be cant make out will start for about 2 seconds then displays code

Hello my question today is with the Samsung dryer looks like it’s the dual element style will run for 3-5 seconds and then shut off. If the power is turned off and restarted on the unit it would start again for another 3-5 seconds and then shut off but if it’s press to start without powering off the unit it will not start again unless it’s powered off. This seems to happen in any mode whether it’s timed or auto. The unit is only about two years old I don’t think it’s running long enough for that motor to even overheat within 3-5 seconds also the unit is that even running long enough to even start to warm up in the 3 to 5 second window.

I would just like to know what to suspect at this point? To check the relay on the board to see if it’s open or is this a known issue ? I have not seen the Samsung dryer do this before

Hello, we just bought a dryer that runs fine then it just stops and sits there and the power button flashes. and as soon as you hit start again run runs fine any thoughts?

Got power, but won’t start

On this dryer the thermal fuse keeps going out, after it runs for awhile? What causes this problem? The vent is clear and is a short vent run.
If this keeps going out should you also replace the thermostats where is down by the heater, or should I look at the thermistor might be bad?

Replaced belt, idler, and squeaky rear bearings first time.. Costumer called me back out two days after initial repair with same complaint.. I greased the stubs for front bearings, replaced front bearings, and replaced rear stubs. Is the costumer overloading? Is the motor possibly spinning too fast? What could be causing the issue to come back? Could it possibly be the motor?
(Lost actual model number the one I entered is same dryer design)

installation instructions for coin drop 7044160P. may need a special tool for access to screws…not sure if reprograming will be necessary…Thanks

so they say the dryer will go off mid cycle.
I checked the motor by letting it run and turning it back on and off and on a d it restarts no problem.
what may I be missing?

I haven’t been on the call yet but I have an LG dryer that has a burning smell once it starts up

I AM TH NKING THIS MAY HAVE BEEN CAUSED BY CLOGGED UP VENT… OR POSSIBLY THE VENTED HOLES MAY ALSO BE CLOGGED OUTSIDE. NEED SOME IDEAS, BEFORE DIAGNOSING THIS MACHINE….

THIS GAS SAMSUNG DRYER IS GIVING THE ( HE ) ERROR CODE ,IT WILL RUN ON FLYFF ONLY WITHOUT GIVING THE CODE. SEEMS TO ME LIKE THE BOARD WOULD BE THE CULPRIT. ANY HELP WILL BE APPRECIATED AND IF VIDEO IS GIVEN IT WILL BE MORE APPRECIATED THANKS

The unit will not power up I need the tech sheet and wiring diagram. 240vac ok and neutral line. Is it the I or main control? Or both?

It starts up it glows then I get a hum from the gas valve but no gas comes out I put brand-new solenoids on it and I get the same symptom the gas valve just hums and then it stops humming it glows again and then it hums again every time it glows it hums

good starting point to troubleshoot this brand new machine…120v ac each leg including feeding back through neutral.5 volts difference between right hot leg and neutral. what the??????

checked components everything checked out fine motor seems it was running slow put new motor in still not spinning fast . what are the facts that affect the speed of rotation

Kenmore dryer 110.66912690

I have checked the dryer and all signs pointed a defective blower motor
I am looking for a disassembly video for this particular model and particularly for replacing the blower motor

Theres no error codes

I have disconnected all other cables from the EOC but I am having problems removing the heater relay power chord

it is an electric dryer.
the drum turns but will not heat

I have a dryer that will not start that kicks out a e5 error. I think its an E looks like an E with the top line gone

When I try to push start to get the control panel to light up. The display board just blinks and beeps once and won’t turn on. Its been doing this for a while and unplugging and plugging back in usually works but is not working anymore.

On this model we have a problem where sensor dry doesn’t stop, clothing is hot, doesn’t shut off and does not go into cool down.

The high limit right thermostat on this unit which would cut power to the motor located on the right side of the heating element , when this goes out what usually is suspected or root cause of that?

do you have a video on this lg dryer. how to get into

MOTOR RUNS, NO HEAT, REPLACED CONTROL BOARD , USER INTERFACE BOARD AND THERMISTOR, HEATER RELAY ON CONTROL BOARD NOT CLOSING, WHY?

error f70

Dryer still not drying properly. After replacing the heat element.

Checked polarity on outlet, check fuse, checked push start switch all good. There’s no power to the start switch. Only place I have power is on the line feed to timer. I’m thinking a bad timer but unsure