1 vote
2k views

it seems that the microwave needs a new mag tube and diode.

  • lopez1974 asked 7 years ago
  • last active 7 years ago
1 vote
2k views

Do you have the service manual for rvm5160dh1ww- is a hotpoint and for jvm7195df1bb- is a GE? The ge comes one but does not heat. How do I eliminate the control board from the magnetron and magnetron thermostat?

  • lue asked 6 years ago
  • last active 6 years ago
1 vote
2k views
  • Pancakes asked 5 years ago
  • last active 5 years ago
1 vote
2k views

I Had a OL reading on a Cavity thermostat. Tech sheet said it was a single pole thermostat and that the contacts close at 158 degrees Fahrenheit. Now i thought this was a normally open thermostat then? totally confused me? Can you ellaborate with this. is that when they close after being heated up, or is this normally open? this is ona microwave btw which i thought would break the circuit.

  • Manlmich3 asked 5 years ago
  • last active 5 years ago
1 vote
4k views

DISPLAY IS NOT BRIGHT, ORDERED PART FROM BOSCH – PART IS UPDATED AND LOOKS A LITTLE DIFFERENT. RELAYS NOT EXACTLY ON THE RIGHT PLACES, BUT THE PROBLEM IS THAT ITS GIVING ERROR CODE E-01
CANT GET IT OUT OF THE SCREEN

1 vote
2k views

Hello,

I have a KitchenAid Wall Microwave/Oven combo. Recently the the turntable stopped spinning. I checked the coupler and determined that it is not broken and suspect the issue is with the turntable motor (the turntable now spins freely, I don’t remember it doing that before). I need to know how to access the underside of the microwave (at least I think I need to) in order to replace the turntable. I’ve looked online and can’t find any videos or instruction on how to do this. Can you please help me with this issue or provide direction to reference materials to complete this task?

Thank you,
Jeff Wessling

  • Guest asked 7 years ago
  • last active 7 years ago
1 vote
2k views

This is an oven/microwave combo. Oven works fine and microwave works good except for it will not run longer than 1 minute. At that point, in the oven control board screen it will give an error code of F3E2. The microwave board doesn’t display this code. The oven sensors check fine as well as the oven works great! Not sure what this could be causing this as all works well except for the 1 minute time issue. Set for 3 minutes will cut off completely at 2 minutes. Any time frame will do the same.you can also start the microwave back up instantly and it will run for 1 minute. Any help would be great!!!

1 vote
2k views

Unit powers on without issue. I had set the timer on the touchpad (for testing purposes) by pressing 1 0 0 0 ( for ten minutes ) and then hit “start”. After I hit the START button on the touchpad, the timer was counting down without issue but the microwave was not on or activated. I could not hear the motor or the fan or magnetron or anything.
Could there be a bad switch on the board inside ?

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
2k views

Without disassembling the over the range microwave. When it operates but will not cook is there a way to determine if its the transformer or even capacitor and Not the magnetron and diode that need to be replaced that you guys state in your repair videos for microwave not heating???

  • Manlmich3 asked 5 years ago
  • last active 5 years ago
1 vote
2k views

I am coming in behind a technician that has been working on this for the past month. He changed the door switches out, no idea what else. All 4 switches test good. Call tech support and they said according to the service manual this model should only have three switches. But all four switches are wired up. I can’t find the service manual can you send it to me. Thanks

  • bean8066 asked 5 years ago
  • last active 5 years ago
1 vote
2k views

No power at all, already checked the fuse and it’s good.

1 vote
2k views

This microwave keeps blowing fuses then it will make nothing appear in the display. It only blows the fuse when the heat kicks on. Any other functions doesnt have an issue, but using the heat will blow the fuse.

0 votes
2k views

How do I access all the components to fix magnetron diode fan capacitor and HV CAPACITOR.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

Microwave blow 1 of 20 amp fuses. Replace it and test circuits before plugging in. Disconnected the mag tube and tested diode gate. Turn power on display came on set the clock. Blower fans works on all speeds. When you set the cook time it the start swich blows the same 20 amp fuse. Looks like a bad short circuit. What do you think the problem can be. I tried everything?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

The board on this unit was flicking off and on and constantly beeping. Will do this while the unit is idle. I changed the control, everything seemed ok, get a call and now the board says needs service and is beeping. Any ideas?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
1k views

Hi,
The microwave blowing fuse, I was testing the switches I found the normally closed one is no good, I changed the switch.
The microwave worked perfectly at that time, now when opened the door again, the fuse blowed up again. Now I need help on what I should do and what is the problem.
Thank you.

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
2k views

We have gone four times to repair this microwave. The customer complains that the microwave does not heat. Initially we replaced the magnetron and it was working. On the second visit we replaced the thermal fuse. On the third visit it was heating but a reset was done aswell as reconected wires to thermal fuse and unit was heating. On the fourth visit the unit was heating but a reset was done again. Now the customer calls is complaing that it is not defrosting and heating, any suggestions?

  • mytechjoe asked 8 years ago
  • last active 8 years ago
0 votes
2k views

microwave worked fine warming the chicken….went to go reheat some vegetables and nothing..heard some popping sound like a fuse but the fan works and lights work and turntable spins

  • leroy needham asked 9 years ago
  • last active 9 years ago
0 votes
5k views

Came across this Samsung microwave with the above error, tech sheet implicates the keypad/control panel. I managed to clean the ribbon cable to the control board and it seems to be working fine now. Could you shoot over the part information for the control just in case I get called back out on this? Want to have that handy.

0 votes
2k views

My Samsung microwave will not start.

0 votes
2k views

My Frigidaire microwave is giving off a burning smell when in use.

0 votes
2k views

My microwave does not heat properly.

0 votes
2k views

My customer has a GE Profile JVM2070SH001 Microwave and reports that the lights on the touch pad light up when the door is opened but non of the buttons will work when trying to start the microwave cooking cycle. any ideas will be appreciated.

0 votes
1k views

My Microwave turns on and everything but will not cook food.

0 votes
1k views

The turn table in my GE microwave is broken.

0 votes
1k views

The turn table is broken on my GE microwave.

0 votes
2k views

Not doing anything.

0 votes
2k views

Had a power surge during a storm and since then the microwave will not do anything.

0 votes
896 views

Hi My microwave is working except for the sensor options. When I press “potatoes” or “sensor reheat” and “start” it flashes ERROR. I tried resetting via fuse; no luck. Time for a new microwave?

0 votes
2k views
Showing 1 - 30 of 270 results