Appliance Type: Stove / Oven / Cooktop

I have a 48″ Jenn-air range ; that main oven flame was sputtering and shut off. I started smelling gas and called gas company they came out and said he had a gas leak. I went out and order a regulator. Replaced regulator unit still does the same thing all other burners are Ok could it be the safety valve?

Oven temperatures fluctuate, over heating, under heating.

Looking for two Thermador hinges part # 00488417
Any help would be appreciated

Another Dacor Wall oven.
Upper oven would no heat, lower oven working fine.
This is a double oven electric. Upper oven would not heat. no power to the element. visual inspection on PCB relay shows the the relay is burnt. put in new board and now “F4” fault shows for both top and bottom ovens. Put in old board and F4 still shows for both ovens.
Trying to avoid having to remove the oven. No wiring diagram. It appears that the oven sensor (upper oven) was replaced some time ago (because of the wire nuts). What is throwing me is that the bottom was working and the only thing that changed was the board and when I returned it to its original state – the bottom is not working.

Any help is greatly appreciated.

I checked the control it seems ok, so I’m assuming it’s the touchpad. Do you guys have some part information there you could pass along for this? Thanks.

Inspected the whole thing no burn marks anywhere on boards everything seems to be in pretty good condition but the oven randomly shuts off usually doesn’t even achieve the set temperature. By shut off I mean it just turns off the baking process as if I never set the bake. The surface burner elements inside the oven seem to be working good and fine customer says it shuts off randomly but for me I noticed it shut off when I open the door The third time while running the oven so I’m not sure if it was a coincidence or if maybe something is loose somewhere inside where I couldn’t see.. I had this issue with another dacor but that dacor completely shut off this one just turns off bake. This one is a freestanding range with the control clock that pops out when you press on it.

Again, this stove is 2 years old and never been cleaned. Never. It is giving off an F10 code when plugged in. I can’t find the make of this anywhere. What is this F10 code?
Thanks

Mod# LFGF3014LBC. Ser# VF25057900

oven wont work I reset house breaker it works when I try again I get error code feature not aavailable theni need to reset breaker and repeat steps

Any idea what error this could be ?

induction burners not working when two or more burners are being used at the same time, ordered pcb inverter assembly # dg94-00728a . needs to know how to disassemble top to replace inverter assembly.

My Electric GE oven is not heating.

Hello, I have an error code E207 for my Bosch oven. The latch does stick. How do I clear the error code?.

Third time I have seen These ranges with this issue they seem to have the same system the old wolf rangEs had like a fireplace or furnace where you hold ignition down until it’s lit. Costumer saying it hasn’t been lighting lately so I’m going to assume it’s that ignition switch?

The wolf oven goes on by itself and turns off.
None of the burners will light without a match

I REPLACED A SWITCH FOR A DUAL BURNER. ALL THREE BURNERS WORK EXCEPT THAT ONE. I HAD NO WIRRING INSTRUCTIONS ON IT.

F79 error code

Need information on this dual fuel wolf stove. How to replace the thermistors in the oven? If you have a break down or know how to get into the oven and change the oven sensors?

The cooktop light on my stove would not go out when all of the burners were turned off. I found your video on fixing the switches when this happens. I was able to remove the faulty switch pretty easily thanks to your video. I am now waiting for the new switch to arrive. In the process, I have left the back panel off of the stove. I noticed last night that when I turn the switches for the burners that are still connected that they will sometimes spark. Is this normal? My fear is a fire hazard. Am I witnessing all of the switches going bad all at once? Or is this normal or possibly just dust getting burned off and once the back panel goes back on will resolve itself.

The switches do not arc or spark when not in use and it only happens when the initial turn happens. So again, is this an issue?

Thank you for your help.

The broil element is broken on this stove. Well, it’s not working, and when it did work it wouldn’t turn off. Now we can’t get it to come on at all. Element itself is still intact and in one piece so I’m pretty sure it’s not that. Found the main control failing and can’t find the replacement available through my vendor. Do you guys have it? I’ll just buy from you if so. Thanks for the help on a weekend!

Error F6 E1 shows on display, Food cooks slowly, Grinding sound from oven.

Overheating condition Error Codes E-0A E-27 E-28.