Appliance Type: Stove / Oven / Cooktop

I just changed both hinges on the oven door but there is still a fill finger gap between the door and oven on the left (when facing the oven) side of the door and you can fee much more heat there than on the right side. Wonder what other issues this could be? I have a new gasket as well. Could the door be warped? Thanks!

I thought it was odd that our stove tripped a breaker, as soon as I reset it, it seemed fine. What should I check on it to ensure it doesn’t keep happening?

My GE oven doesn’t seem to be cooking correctly. It beeped like it preheated, but when I put dinner in last night it didn’t cook it. Hours later it still wasn’t done. Burners on top work fine, checked to make sure it was getting gas. Maybe a thermostat?

I can scan a photo of the stove. The florescent light bulb us just behind the clock, etc and is 36:inches in length. Do I have to move the stove away from the wall to replace the bulb, or is there an easier way?

coming for dinner and one of my burners is stripped.
my number is 412-580-5300
thanks
fred

I have a couple elements that have gone out on my stove. Is this pretty easy to do myself if I buy the parts? Don’t want to put a lot of money into this thing cause we’re moving soon. Couldn’t find a video so hoping somebody there can.

Our oven worked perfectly through Thanksgiving (thank goodness!) but last night I’m pretty sure it didn’t heat up to the preheat temp even though it said it had and beeped as if ready. Dinner took much longer than normal to cook and I’m wondering if something isn’t right. I’m going to have my boyfriend take a look at it if someone could point me in the right direction on what to check?

I’ve got this thing apart and have been checking parts to find the problem. It was tripping the breaker consistently and now I’m not sure what’s causing it. Checked the board, seemed fine. Checked the igniter, also good. Getting proper power to and from unit and the wall, so can anyone help me out?

I replaced the clock oven control unit with a like part. Made all connections same way as on old part.
Still no heating to burners or oven. Clock will light and ask to reset time, but goes off when turn off the knobs to burner.
Is there some other part that could be bad.

No heat to burners or oven,

I’m getting an error code on my oven display that I looked up and it says it’s for the probe? But my husband checked it and it is working properly. So what do we do now? I don’t want to replace it anyway if it’s fine.

Is this my thermostat causing problems or maybe the control? I need to get this going for the holiday. Would appreciate some help.

My gas stove has three smaller burners and one large, hotter burner on the front right side (in my house, next to the wall). Can the large burner be moved to the front left side, next to the counter, where I would use it more easily?
thank you!

How to get smooth top off to change out element

the oven comes on, and eventually heats, but seems to constantly re-ignite. the heat element stays on, but the gas flow seems to stop then come back causing a re-ignition of flame. It does longer than it should to reach temp and then has difficulty maintaining.

After speaking with the Kenmore service and parts department, they concluded that my gas valve to bake was either clogged or broken since the broiler element works and we didn’t smell gas when we tried to use the bake control. I didn’t find a video on how to replace or clean the gas valve. We got down to the valve but don’t know where to go from there. Do we access it from the back to replace it or do it from the oven? Do you have a video

TURN ON AND IT FIRES UP THEN SLOWLY DIES OUT..CAN NOT LIGHT…

Our range is beeping non-stop and flashing the aforementioned error code. From what I could find online, this is a shorted keypad. So what part do I need and is there a video that could show me how? I really don’t want to have to get a new range and am hoping this won’t be too difficult.

when i turn on any top or oven, it will come on and die out..then i have to leave ignitor on until it comes on and stays very low flame before going to proper setting..

I have this gass stove , kitchenAid Model # KGRI801PBS00.
Costumer complaint: make short circuit , tripeed braker (or blow out braker) at braker box , then He restore power and blower motor kept running all the time ( non stop).
I take off the touch panel with the control box behind the touch panel and restore power blower fan motor kept running , so, I hit with my screw driver the relay board , the one is located behind the surface and get the motor stop .
But when , I put back the touch pad with the control is at back the touch panel and press the bake , the braker at braker box when off again (braker tripped).
another interesting question that I have is: I take away the cables going to the motor and check those cables for ground it was grounded , when the plug is inserted in the wall outlet, but if , I take away the plug from the wall outlet , now is not grounded is that ok?.
Now I , think I have problems with one of the board ,but I don’t know , which control board or even if the touch panel .
How I will determine or probe each one of this control or touch panel. thank for your help, wating for your answer, my email address is : armandoappliances@gmail.com , or also I have this other one : armgua@gmail.com. I am fan of yours wabesite and also I was refered to you, by marcone appliance which , we have accesd I belive as a premium till December 31.

I have a double oven maytag and my bottom oven will not heat up when I turn it on to preheat it stays at 100 degrees. I replaced the bake element so why won’t my oven heat up?

whats died so I can fix it fast….

TRIED TO CHECK BAKE ELEMENT. CUSTOMER SAID NOT BAKING GOOD OR GOING INTO SELF CLEANING. HOW TO GET TO IT?

Broiler on oven won’t shut off

If the igniter is broken, does the oven still send gas to the burner tube when turned on?  I only ask as it’s not lighting, so I tried to turn it on and light it manually, and apparently there’s no gas coming from the burner tube.  I just want to make sure the igniter is the problem.  Everything else works on the oven – all four top burners and the broiler. which is at the top of the oven.

The entire touch pad works except for Bake, Broil, and convection. All the digits and timers clock keep warm, pizza, the rest of the key pad functions. Tried to reset by unplugging. Didn’t work. Oven comes on by using the pizza function. Top burners work as well. Why only a few not work?

light in the oven is always on , the turn off key seems is not working and as well some other 2 o 3 keys. my guess is i need to change the membrane, but , how i will konw if is just the membrane and not the the coen ntrol too. there is not teck sheet in the oven or else where. i do not want to give a wrong estimate to my costumer because the control is too expensive, one of the control is $279.17 and the membrane $140.00 if i added together both is so much. menbrane pt# 9756595bt- control pt# 9762812