Appliance Type: Washer

When I arrived the water valve put in a little water and then the drain pump came and continuously ran and when I went into service mode the error codes E30 and E54 were in the history. I went through the test options and made it T06 which is the pressure switch test and it went into error. I put a pressure switch on the washer and problem still occurring with the same symptoms. Thanks in advance for any help

Has blinking code e68

I’m pretty sure this will be the belt due to the customer’s description and finding pieces of rubber on the floor. Whats the part number for this?

My customer had an electrical outage the night that we had an electrical storm. He lost his cable, dishwasher, and all cordless phones.
His washer only fills, then he has to change the setting from wash to spin and drain. And only then will it empty. That’s all it does.
Is it possible that the machine got hit as well, and did something to the board? It worked fine up to that point.

It fills at the proper levels, but won’t wash.

How do you know if these componet didn’t short out parts on the mother board? Where wold you start. Replace all the components under the machine first then try to operate and if doesn’t work replace the control board.

I HAVE A CUSTOMER THAT HAS A COMMERCIAL MILNOR WASHER. THE UNIT WILL GO THROUGH CYCLES UNTIL IT REACHES 19 MIN. IT THEN STAYS IN THE WASH CYCLE AT 19 UNTIL IT SHOWS A CODE FOR A BAD PRESURE SWITCH. I CHANGED THE PRESURE SWITCH AND CALIBRATED IT. WHEN I LEFT IT, THE UNIT WAS DOWN TO 15 MIN. I WILL CALL TO FIND OUT WHAT IT DID. IT SEEMED TO ME THAT THE CYCLES WERE TAKING TO LONG, AND NEVER DRAINING WATER EVEN THOUGH IT SAID THE UNIT WAS IN THE DRAIN CYCLE. ANY GUIDANCE OR HELP WOULD BE GREAT, THANKS, TODD FROM NY.

Unit not draining. Tried the drain pump and still no drain. 110v coming from both lines (separate readings) to drain pump. Thinking it does not have common. Believe it is the board. Looked on older USB and not their. Anyone have some info on this unit. Thanks in advance

GE front load washing machine. When you turn the machine on and hit start, it does not do anything mechanically (will not fill with water, spin, etc) but it shows the cycle counting down on the display. Pump made a noise one time but that is it. We suspect a control board but are not confident.

NOTE: I placed two black lines on my tub and agitator to observe individual movement.

Initial observations of the Problem:

My top load washer “roared” in either the rinse/spin and completed the complete cycle. (I should have paid better attention to detail.) In the 2nd rinse the washer stopped with water in the tub. I noticed a burning smell and the motor went into thermal shutdown. As I removed the V-belt I noticed much black rubber from the belt( V-belt track was cut). The water pump pulley spun with great difficulty. When I tested the transmission via spinning the transmission pulley counter clockwise (CCW) the tub spun CCW. When I spun the transmission pulley clockwise (CW) the agitator moved CW, however I don’t know it is agitating since I’m doing this task myself.

I believe the water pump pulley bearing cause a lockup such that the V-belt burned rubber. The electric motor recovered from thermal shutdown and turned on after allowing it to cool and with the V-belt removed.

Questions:

1) If the transmission pulley is spun CW what should be seen? Should the agitator spin around the 360 degrees? Would the agitator spin “X” degrees and then restart?

2) Could there be something else wrong with the agitator if it spins and doesn’t agitate?

3) What is the best way to check thrust bearing when the pulley is all black and I don’t see the “markers” the new translucent transmission pulleys contain?

4) Is it possible to just replace the water pump bearing?

Summary:

I know the belt and water pump need fixing or replacing. Questions #1and #2 are the most important since if the transmission is smoked there is a big cost. If you can provide answers to the all questions great?

Thanks in advance,

JP

unit will wash and drain and shuts off with 8e code be for spin.

My washer is stuck. The motor to drain stays on. It still runs with lid opened or closed.

Everything works except there is NO agitation during wash or rinse cycle. Washes, drains and spins fine

Error f6e1 and f3e2 I replaced ccu did not fix wires are fine do you think it is the ui or mcu

this LG top load washer goes off balance almost every load. not loading or doing anything different than I did in the past. started doing this 2 months ago. Is it the balance ring, suspension rods, need software update, or combination of all? I can hear water in the balance ring, has some of it leaked out? Bearings and tub are in good condition. tub nut is not loose and bearings are not worn or loud. machine is level and firm on the floor. I have read this is a very common problem with LG top loaders. Select Normal cycle, fills, agitates, then after a few minutes starts spinning in one direction with clothes and water, tub starts banging against side of washer. Then it stops and reverses direction, spinning with clothes and water, bang, bang, bang, stops and goes back to agitating. The machine will do this with no clothes in it, on the normal cycle.