1 vote
3k views

Our Electrolux refrigerator dispenses ice intermittently. It spits ice out on the floor. We have had to shut the water off or it will spit water also. With the water off you can see and hear the dispenser turning on and off at all hours of the day or night. I need to dig into the parts to see if it is a loose wire or faulty control panel?

I need help with how to pull the stainless ring off the control panel to get at the parts.

Has anyone solved this issue before?
I have seen it reported as Casper the friendly ghost.

Thanks,
Tom

  • Guest asked 6 years ago
  • last active 6 years ago
1 vote
2k views

I need to remove the stainless steel trim ring that surrounds the ice/water dispenser. Do you have a technical manual showing how to do this? I don’t want to damage it. I don’t see any exposed screws.

  • Guest asked 6 years ago
  • last active 6 years ago
1 vote
2k views

I NEED TECH DOCUMENTS, SCHEMATICS, REFRIGERATION SHEETS PLEASE

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
2k views

filling and draining at same time. leaking on floor

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
1k views

water presssure switch working but always 120 on the wire for no o water switch. dont have any diagram or nothing to follow.
motor controller board changed already but still not working

  • Guest asked 7 years ago
  • last active 7 years ago
1 vote
1k views

The customer showed me a video that sounded like the pump running with the door open. She said that it shows an error code often of 10 and last time it showed 30.
Where is the tech sheet hidden? I couldn’t find it behind the door panel or behind the toe plate.
I need a copy of it and the error codes and videos.

  • Guest asked 5 years ago
  • last active 5 years ago
1 vote
2k views
  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
2k views

we need a video on how to dismantle the dryer

  • Guest asked 5 years ago
  • last active 5 years ago
1 vote
2k views

Dryer still not drying properly. After replacing the heat element.

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
2k views

The dryer takes 3 hours to dry a load. I checked the vent lines, filter, replaced the heating element along with its thermostat.
I looked at the parts diagram. And what is the purpose of the Control Board,temperature,ATC ?
Should I replace any of the thermostats?
I put my temp meter on the inside wall of the dryer vent as it ran. its temperature went from 111* to 138* on time dry and It slightly rose and fell in a time of 5 minutes On more dry setting it red 128* to 148* slightly rising and falling in a 5 minute time.
Should the temperature stay or maintain a setting of ( let’s say ) 145* for a time of 5 minutes? And then gradually drop and stay at 120* for a couple of minutes?
This dryer is giving me heart burn.?

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
4k views

Hi,
I am trying to determine what part I need to fix my dryer EFME627UTT1. Essentially, the dryer won’t start. However, it is exhibiting other strange behavior. The dryer has been in service for about two years since, 9/2019.

When I try to start the dryer, it makes three beeping noises, as it would if the door was open. The door is of course closed however. I put the dryer in diagnostic mode and it displayed an error code of ‘EHd’, flashing as ‘E’ then ‘Hd’. I do not see that code listed in the Dryer Tech Data Sheet. The dryer has a wheel to rotate through the different dry cycles. The center of a wheel has LED lights on it, indicating the time left to complete the dry cycle in minutes. When I rotate through the different dry cycles, the timer doesn’t change as it normally would. It gets stuck on particular value, once at 45 minutes, once at 55, etc. Additionally, sometimes the previous mentioned LED light doesn’t come at all when I start the dryer. However, if I put the dryer in diagnostic mode, the light will then come on and display the error code ‘EHd’ as mentioned previously.

I have taken the dryer apart to check for lint buildup, I found some, but nothing extraordinary. I am assuming its some sort of electronic problem. From some googling it seems it might be the control board, but at around $150 I’d prefer not to miss the call on the diagnoses. Thanks for the help.

  • Guest asked 3 years ago
  • last active 3 years ago
1 vote
2k views

When I try to push start to get the control panel to light up. The display board just blinks and beeps once and won’t turn on. Its been doing this for a while and unplugging and plugging back in usually works but is not working anymore.

  • Guest asked 6 years ago
  • last active 6 years ago
1 vote
3k views

I’ve been noticing ice buildup in our freezer, and water gathering on the shelves in the refrigerator. Where is this water coming from?

  • Darren Boyles asked 11 years ago
  • last active 10 years ago
1 vote
2k views

Door does not lock

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
3k views

THE UNIT COOLS FINE, HOWEVER, THE “DOOR AJAR” ALARM LED IS LIT AND BEEPS. I HAVE GONE THROUGH THIS UNIT AND COULDN’T FIND ANYTHING WRONG WITH THE INTERIOR LIGHT CIRCUIT, WHICH IS CONTROLLED BY THE DOOR SWITCH. THIS LED ME TO BELIEVE THE FAULT WAS IN THE BOARD. I HAVE A NEW BOARD INSTALLED AND HAVE THE SAME ISSUE. ANY IDEAS? THANKS

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
2k views

video on how to replace rack sensor

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
3k views

I’ve tested the air flow with a meter it is poor I’ve tested the igniter everything else inside is working fine there was a tremendous amount of lymph build up inside the machine cleaned everything out and still getting poor airflow reading

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

This is a Kenmore refrigerator that is built by Electrolux . It is a french door bottom freezer. There was a frost build up on freezer evaporator coil. We defrosted it and a week later it built up again. Defrost heater and termination switch checks out. What else can it be?

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
3k views

I have a customer with an upright freezer. It stands taller than a regular fridge. Well I’ll get to the point. After diagnosing the problem, I proceeded to put the back evap cover panel back on AND I put the screw right thru the coil tubing. Ah s#~}%~~! I couldn’t believe that the screw hole was a 1/4 inch from the coil.
Well ” things happens” and it seems to happen to me an awful lot. The model / serial numbers that I gave to you, are barely readable, so I don’t even know IF they are correct. I offered to work something out with the customer, which turned out FOR ME to be a nightmare. She is a pack rat. It took me over an hour to remove the freezer from her house, because there was ONLY a path to get from one room to another. She had junk everywhere….
I took the freezer to a fellow repair tech that fixed the hole, blah blah blah. An hour after I dropped of her freezer, she called me to find out the status on it. One hour! I got several calls. So, I just stopped picking up the phone.
I offered to turn the case over to my insurance company but that was not an option…. So, I can’t tell you how many hours I spent trying to fix and satisfy this customer.
Here is my question, for further reference. I’m NOT going thru this again. Is there a website or something that I could use to determine the value of an appliance, and just pay the customer a fair price ?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

my ice maker has quit making ice and the ice in the bin has melted. I suspect it might be a thermistor but not sure. If the thermistor was bad would it explain the change in temp in the ice maker compartment? All other areas are working fine. is there a diagnostic I can run on the unit? Code? to verify if the thermistor in ice maker is working correctly? Also, i show there are 2 different thermistors in the part diagram , can you tell me the difference. Thanks for your help.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
6k views

Hello, I have a dryer the is showing an e71 error code. all the sensors are checking out good the only thind is one of the 3 coils is bad would that cause an e71 code?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

No cool in fresh food section, Unit continually runs, Will not run.

0 votes
2k views

Squeaking noise, will not always spin, burning smell.

0 votes
2k views

My dryer powers on/off via power button just fine. The knob selector also works appropriately. The start button does not always register being touched. Likewise, other “buttons” do not sense being touched (Temp, dry level, dry time, options, set, cancel). When the dryer does start, there is a lot of rapid beeping during the drying cycle. I cannot enter into diagnostic mode or perform a factory reset due to the lack of response to the key pad. I attempted to replace the UI board (part # 5304505611) but that did not resolve the problem. Last night, after managing to get the dryer started and run through a complete drying cycle, the unit restarted on a cycle without the unit being touched.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
11k views

Customer says that they can only turn on one out of four burners. one comes on and when they attempt to activate other burners, they get intermitent flashing LED lights on readout. There are two LED readouts. one on left and one on right. after they activate the one burner and start to activate the others, the error code appears. left LED displays
” E ” and right LED displays ” 32 “. Sounds like control board but not sure.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

The washer only leaks when in the spin cycle. When washer goes into spin it will start leaking from the center where the transmission goes thru the tub and it makes a grinding noise. If I replace the spin bearing will it also stop the water from leaking. Thanks Ricky

0 votes
2k views

Your video shows how to diagnose the problem, but not how to fix it. Thank you for for the diagnostics, video that was very helpful. I really need a video to remove and replace.

  • Christina asked 10 years ago
  • last active 10 years ago
0 votes
2k views

Power outage, temp. alarm comes on, won’t stop. no response from display board. Replaced connections on display board.
Now I get response from display board but nothing else comes on.
Reset power one more time- Compressor comes on, stays running but interior lights and display beep and flash, total power interuption to everything but the compressor.
Does this still sound like the main control at the bottom?

0 votes
2k views

My Electrolux refrigerator is not cooling properly.

0 votes
2k views

My Electrolux washer seems to be off balance.

Showing 1 - 30 of 202 results