error code e- 01 and e 24
drain pump has been replaced and it will not go the complete cycle
- Guest asked 8 years ago
- last active 8 years ago
the unit will start it’s count down and then stop mid way.
the soap dispenser will not dispense.
and they hear a humming sound comeing for from the unit
- Guest asked 8 years ago
- last active 8 years ago
My Samsung dishwasher is displaying a 4c error code.
- Don Kopecky asked 8 years ago
- last active 8 years ago
My Viking dishwasher is not working properly.
- Patrick's Appliance Service asked 7 years ago
- last active 7 years ago
My Bosch dishwasher is leaking water.
- Curtis Appliance Repair asked 7 years ago
- last active 7 years ago
My samsung dishwasher is displaying an error code and i cannot get rid of it.
- T&G Appliance Repair asked 7 years ago
- last active 7 years ago
I sent a question earlier and forgot to put the information that I need to share, I cleaned the dishwasher that was very dirty and so I cleaned it and it ran good for 3 washes and the customer called and said it stopped working,
thanks
- Guest asked 7 years ago
- last active 7 years ago
Could that be the touch pad? dishwasher works fine at times. It is not the drain!
- Guest asked 7 years ago
- last active 7 years ago
It seem like the circulating motor is not working a nd the tech sheet is missing, so I can’t check the circuit board.
- Guest asked 7 years ago
- last active 7 years ago
I’ve tested the heating element and thermostat. Both test ok. Not sure what else to try besides replacing the control board.
- Guest asked 7 years ago
- last active 7 years ago
Customer called and complained about dishes not being clean on bottom rack.
- Guest asked 6 years ago
- last active 6 years ago
The rack in my dishwasher keeps coming off track.
- James Buchanan asked 6 years ago
- last active 6 years ago
WHEN TURNS IS ON IT STARTS THE WASH CYCLE THEN IT STOPS. SHOWING AN ERROR (HEATING). SPIN CYCLE DOESN’T DRAIN BUT SHE SETS IT TO DRAIN AND IT WILL DRAIN.
- Guest asked 6 years ago
- last active 6 years ago
Unit will not start, Control Panel will not respond.
- David Sutton asked 6 years ago
- last active 6 years ago
LG dishwasher will intermittently show a drain error code. When this happens the machine will just sit and do nothing. If restarted it will run the cycle.
- Guest asked 6 years ago
- last active 6 years ago
Hello, I just replaced the defective touch panel. I need to know how to clear the error code on this model. Maytag dishwasher MDB4949SDZ. Thank you, Shawn
- Guest asked 6 years ago
- last active 6 years ago
My Jenn Air dishwasher JDB1270AWY has started making a grinding noise during part of the cycle. It is cleaning great and seems to be draining fine. Ideas?
- David Sutton asked 6 years ago
- last active 6 years ago
Frigidaire dishwasher not working. First it would not drain. Got all the water out with a shop vac and cleaned the drain. Went to test but not nothing happens. Lights come on and it switches over to washing but it’s quiet. No water to the dishwasher. Was thinking maybe float switch/relay.
- Gary Williams asked 5 years ago
- last active 5 years ago
I have a Bosch dishwasher model SHP65T52UC/07. I replaced a broken handle on the door. Manufacturer Part Number: 12012912. I mistakenly removed the 2 screws holding the door hinge on the right side of the door when I removed the door panel. This resulted in a great deal of effort and consternation for me to replace the screws in the hinge. When I disassembled the door panel a wire came loose. It is the red wire at the center of the controls. I replaced the wire, but I do not have power to the controls. Could I have disconnected any other wires that are not visible to me or is there some other cause of the lack of power? I have checked my circuit breakers and I have power to the junction box where my dishwasher power cord connects. The breaker did not trip. I have tried to reset the dishwasher by pressing the start button for 3-5 seconds without success.
Dave Griffiths
bvfalls21@yahoo.com
5038662617
- Guest asked 5 years ago
- last active 5 years ago
Dishwasher will fill then just set. After a long pause it will pump out but does not run the wash motor. Ran the diagnostics and came up with f6e6. Don’t know what this means the codes are not on the diagnostic chart that is with the dishwasher. Any ideas what it means.
- Guest asked 5 years ago
- last active 5 years ago
My dishwasher buttons are not working. I am getting bE error code.
- Curtis Appliance Repair asked 4 years ago
- last active 4 years ago
My Kitchen aid dishwasher is not cleaning properly.
- Harley Clark asked 3 years ago
- last active 3 years ago
the programming starts normally, water and washing works, when it is on the programming to drain the water the pump does not turn off and shows error I30, I have already replaced the board and the same defect continues
- Guest asked 2 years ago
- last active 2 years ago