Appliance Type: Dishwasher

My dishwasher is giving me an OE error code.

My dishwasher is displaying a 5E error.

Error code on my Samsung dishwasher.

My dishwasher is displaying a 4E error code.

My dishwasher is displaying a “PE” error code.

My Samsung dishwasher is displaying a 9E error code.

“IE” error code

My dishwasher will not run and is displaying “HE” error code

This GE dishwasher is flashing lights when the door is closed like it is open. So we believe the door switch isnt working. We don’t know how to take this door apart because there are no screws.

This Bosch dishwasher ,will run an entire cycle but if the cycle is cancelled or completed then it will flash 0 then will refuse to do anything. Won’t respond to

This dishwasher is about 5 years old. It is not heating or drying the dishes but runs the cycle as normal. The next thing my tech thinks is there is a wire harness with a thermistor on it that my tech thinks could be the issue. We wanted to get some advice before we try this route.

I have changed the drain hose and pump but it still won’t drain.
Is there a check valve in the module?
Can it be the diverter motor?
I can blow air through the drain hose. The drain pump works fine.
What else could be the problem?

It will start and run for awhile and cut off.Then when you restart it, it runs for 10/20 seconds and cuts off, restart and runs for 10/20 seconds. You get the idea. Please I’m old school, need help telling me what to check and how. Don’t like to have to ask, but i’m new to all is electronics stuff. Thanks Chip

the top rack left front mount that goes into the rail is broken. we need to know how to replace

My dishwasher overflows after about 5 minutes of running. Not sure where to go at this point after everything i’ve tried to fix it so far.

Asko Dishwasher fills, clicks 3 times, flashes “delicate wash” after new inlet valve installed, old valve was leaking bad, new valve seems good fills to the proper level as far as i can tell but cycle doesnt continue. Tested resurculation motor that tested good and had continuity and their initial complaint was leaking which it no longer is leaking. drains fine, water switch and door switch seemed to be fine..?

All others work. I need a tech sheet or service manual with the ribbon interface test for the console so I can diagnosethe problem.

Hello, I just want to say I have not idea how to work on a dish washer but there is not to much to them. that being said I have a dish washer that runs and finishes but has water sitting in the bottom. I took it apart and there is nothing in the pump. when I send it in the drain only I can hear the pump running. I also checked the tube going to the drain and its not plugged. what now bad pump?

wash motor turns of after about 15 minutes of run time…motor won’t start again on any cycle or in diagnostics. Cycle continues to end. Motor will start again after a period of time but does the same thing. 1 diagnostic code 4-3 motor not running. d/w 1 1/2 yrs old

This unit stopped working after a storm took the power out. I have verified that I am getting 120vac at the main board. The user interface is completely dead and unresponsive though. I have tried to put it in diagnostic mode and it does nothing. No lights at all on the user interface.

I have this Whirlpool dishwasher that I replaced a broken heating element and once I replaced it I tested it under a diagnosis and LOAD test I was able to confirm that this heating element is working and heating however, when I use it in normal mode it does not heat as far as I understand that the error codes have to be cleared in order for the heating function to work again. I did try the service diagnosis by hitting three buttons 1-2-3 1-2-3 1-2-3 and going into that and getting into service diagnosis mode run and letting it complete Is there a step missing as far as clearing the error codes from this ?
If the error codes are not clearing does mean a faulty computer?

During heavy wash cycle at about 6-7 minute mark water will come out of overflow on right side of dishwasher. Can’t see where water coming from. All seals good and washing normal but for some reason water leaking thru overflow.

DISHWASHER WILL NOT DRY DISHES WELL, HEATER HAS BEEN REPLACED AND DOES HEAT BUT CUSTOMER STILL COMPLAINS THAT DISHES ARE NOT DRY ENOUGH, WATER DOES NOT GET HOT ENOUGH.

LOOKING TO SEE IF THERE IS SOME SORT OF A SERVICE UPDATE FOR THESE NEWER STYLE WHIRLPOOL DISHWASHERS, WE SEEM TO RECEIVE MANY COMPLAINTS LIKE THIS.

THANKS