Appliance Type: Refrigerator

are you sure your video for ice maker removal is complete?

Hi thanks for your video on how to replace my ice maker it worked great. However my ice maker still does not make ice. It seems to cycle one time and then quit. So if I reset it it may make one tray and that’s all. Same results with the old ice maker I replaced. Any ideas?

My fridge isn’t cooling. The evaporator is only frosted on about the top 1″ of the evaporator. I’m aware that the evaporators are notorious for leaking. How do I locate the leak? Will a leak that small show up with a bubble type solution, or do I use a sniffer?
When it comes time to evacuate the system, I have manifold gauges, but they’re set up for automotive R134a. What are the correct fittings for the R12 system? It looks like 1/4″ flare, but I can’t tell for sure. In the automotive world the low and High side have different size fittings, but on the fridge they look to be the same.

Thanks,
Don

Have E 22 fault code which I know is the fresh food fan. Problem is code will not reset and nothing else will start up on the unit. Can here the control board click but compressor never cuts on. Any ideas?

First, your subzero refrige coil repair video is great!!

We have two Subero units with the 2 compressors in a tray. The 700 series and also a 427 wine cooler with lower drawers.

These units are a nightmare to work on due to limited access.

Since there is nothing obvious about how one might be able to ever get to the back compressor for service, a video would be a huge help.

Are your tech people familiar with these units with the tray, and would they consider a video?

If not, is there anyone there who I could talk to on the phone about the tray style subzeros?

Thanks

Whirlpool Refrigerator French door bottom freezer. The unit is all iced up where the Ice maker is? How to you take the Ice maker out? It has all snap parts with screws to come out.

SPECIFICALLY THE PROCEDURE TO RECHARGE THE SYSTEM AND SCHEMATIC.

TX

refrigerator is not cooling at all but the compressor is running

Just looking for any service pointers ,, videos ,, wiring diagrams and diagnostics for this icemaker ..

The ice maker door was clicking. I put a new HV circuit board in the back of the fridge and that stopped the ice maker noise. Now the front panel is flashing PE0000. The compressor sounds like it is always running. The front will let me dispense water, but nothing else. It will not respond to any button trying to reprogram it. I tried the Door alarm button and held it for a while and nothing. tried the Water button and held it for a while and nothing. When I push the + Or – on the refrigerator side the display will show ICE or H20 in the display. but nothing else will respond.

I need some advice from our subzero experts.
Complaint: Not Making Ice.
We found the unit with the icemaker arm bent around from the bucket being pushed back on the arm.
We replaced the icemaker and as the water level was low and it is in a rental home we removed the filter and installed a factory by pass plug.
I started the unit in Max Ice. The icemaker cycled around twice and filled to the correct water level. We thought all was good and stopped to double check it the next day, No Ice.
I checked everything over again, drawer switch etc. ok.
After posting on psanet we replaced the complete water valve w/flow sensor. I opened the valve sensor and found it had droppings in it. We thought we were ok.
I started the icemaker again on Max ice and stopped to check it again 2 days later. Still No Ice.
The wiring seems good . Power to the flow sensor comes from the Low Voltage Board and Power to the icemaker comes from the high voltage board.
Factory tech line doesn’t think it is a board.
Any advice would really be appreciated.
Thanks in advance.

Hi,
I am troubleshooting a no LED light issue on this unit, All the LEDs work except the 5 on the roof of the refrigerator. The schematic shows that the 5 fridge roof LED’s are divided into 2 series circuits, 3 in one series and 2 in the other going back to the LED Driver board for the DC source. Both of these strings are not working, I have diagnosed that the LED Driver board is partially defective .

The problem is, it is not shown in any service literature, ANYWHERE. The visual shows it is located next to the control board along with the power supply, The only part shown in the exploded diagram is the Control board itself, Whirlpool W11161172. If you do a parts list search for LED Driver, it does not generate any hits. I am at a loss, I have check multiple sources including the Factory SM with no luck.

I need the part number for the LED Driver Board! Why is it not shown or listed anywhere? I wasted 2 hours looking!!!

Thanks 🙂
Tom
609 418 0278

Condensation back wall in refrigerator and behind ice maker

No matter where the control is set it freezes every thing.
How do I test this unit?
I need a service manual and tech sheet and any advice you can give

This is a French door refrigerator. The ice room drain freezes up and the air vents fill with water and freeze.
Has frigidaire ever found a sure fix?

Condenser fan cycling on and off every 10 seconds. everything else is working fine.

Customer said that ” Feezer works fine. Its cold in there but the refrigerator is warm. ” I have handled this symptom before on other manufacturers but dont want to assume same cause. Usually frost build up in evaporator coils in freezer section which constricts airflow to fridge section. Should I test defrost heater before testing defrost thermostat or defrost control ?

Kenmore fridge

Model Number
106.57036601
What have you tried so far?
Customer said that ” Feezer works fine. Its cold in there but the refrigerator is warm. ” I have handled this symptom before on other manufacturers but dont want to assume same cause. Usually frost build up in evaporator coils in freezer section which constricts airflow to fridge section. Should I test defrost heater before testing defrost thermostat or defrost control ?

Refrigerator Kenmore
Share
semperfi asked 3 days ago
Answers (1)
Sort by: Newest First
0
0
Hello
You need to check first if their is a heavy even frost build up on the coil. Then next do a continuity test on the heater. If the heater has continuity, then check the defrost thermostat. If the heater and therm. are good then replace the adaptive defrost control.
Information Links
106.57036601 Manual Sears refrigerator | Adaptive Defrost control | 4388932 Defrost control video

The unit is showing me a R10a code that the ice maker sensor is open or shorted. But all the tests are fine for the Ice maker sensor. the temper and ohms correspond to the chart and the dc voltage is 3.0 at 39000 ohms. The ice is forming on the inside of the refrigerator corresponding to the position of the air passage from the freezer to the ice room in the refrigerator. That is also where the water under the pantry drawer is coming and not the fresh food evaporator drain. It said in a manual for another samsung to check the thermister reading at the display but I don’t see any information how to program it to show that or any thermistor temperature except the normal operation readings of the actual temperatures. Isn’t there some way to run the damper and lights and evaporator fans ect……? Is there a better service manual for this and if you have ever seen this kind of freezing in the air passage, what did you do?

Hello, I love your new website.
My customer has a GE French Door fridge with the freezer on the bottom. I think the board that controls the fans is bad. I am the forth technician to service this fridge. She has had nothing but problems with it since she bought it. A year after, GE replaced the compressor. After that 3 boards were replaced. And more! Now this?..