Appliance Type: Stove / Oven / Cooktop

The back left burner on my Whirlpool range is not heating.

I have a Sears stove mod. 629.46795892. When power is on the cooling fan comes on within 30 seconds and f1 comes up. And some thoughtfull ass took the tech sheet. Can you tell me f codes and what f1 is. I thought it was the e.o.c. Thanks for all your help.

My electric whirlpool oven is not working.

my Frigidaire stove is displaying an F1 error code, keeps beeping and will not shut off.

My Bosch oven displays “224” error and will not come on.

My kitchen aid oven will not turn on, also door will not open.

The element on my Hotpoint stove is not heating, also the clock is not working.

Unit will spark but wont fully ignite.

oven turns off

The large oven tends to take a longer time to preheat, even though the hidden bake element and the broil element are cycling during the preheat. Also, should the throat elements be coming on to assist pre-heat, or are they only used to convect?

My name is Roland,
Question: I am working on a Kitchen Aid dual fuel gas range MD# KDRU7893VSS03 SN:DB1375935. The issue with this unit is there’s an error code which says NTC out of Range. I have tested all fuses in the back of this unit, I have changed the sensor -W1076760, the boiler assy -9758598, the appliance manager-w10339702. Still when power up, it goes into lock out with NTC out of range, call for service.
Can anyone help with this issue please. I await your response.
Roland

I have this double wall oven. The MW display says door. I have run into this before but those MW’s have two cartridge fuses, and one would blow. This MW only has one fuse and it is good. The door switches checked good, but I replaced them anyway, still didn’t work. Anyone have an answer or suggestion ?

I am looking for fault or error codes for the model below. Thanks in advance for your help

Indicator light stays on 24/7

Looking for the ignitor on this model

I have a maytag gas range the oven will ignite but only burn for about 5 seconds any help would be appreciated thanks.

The left side cooktop burners are only heating to the highest temperature setting. I think the left front dual burner switch is bad but am having a tough time with the lookup on my phone. Any chance you guys have this handy?

Just had a customer call me about a gas oven with two of the burner putting off a yellow flame, you guys ever heard of this? Not sure what I should take with me to replace, if anything. Said they are still working and heating without a problem but was just concerned that the color was so off and called me to come take a look. Thanks you guys.

I think I need a control panel but don’t know the specifics.

The front right burner isn’t lighting or working at all. Does this come as an assembly? I think the entire base comes with the components/parts included but wanted to make sure first before ordering.

What part do I need to fix this? Think it’s just the element.

This customer had used the oven for about four hours earlier in the day. The oven was off and the bake element shorted out. I know there is always 110v volts to one side of the element. Is it common for an element to short out on it’s own when not in use? Customer is worried that there may be something wrong with the control board. I replaced the bake element and checked for power from the board. The only power present is on the one side coming from the terminal block. Control turns the element on and off with no problems. Control board has no visible problems and is working fine. Is there any concern here? Thank you in advance.

Hoe to remove control panal

I have a GE stove, need to change door springs how do you remove the tracks from bottom draw to gain access to little door to change spring any help would be appreciated thank you

Good day Gentlemen,
My name is Roland, I am working on a KitchenAid duel fuel range. The issue is the open burners work, however, the oven and all it’s functions dose not. The interface board will not reset from PF Code. I end up replacing the relay board and the interface board on this unit. I attempt to enter the clock info. but all I am able to do is get the unit to show a series of _ _ _ _ _ _ dashes on the display. I am able to cancel and restart, but it continues to come back to the same thing, a series of dashes. Have anyone had the experience with this unit and this issue before.
Thank you
Roland

Looks like I’ll need information on the electronic control for this, will confirm for sure when I get there but want to be able to have a handle on the parts needed before I walk through the door.

The broil element is broken on this stove. Well, it’s not working, and when it did work it wouldn’t turn off. Now we can’t get it to come on at all. Element itself is still intact and in one piece so I’m pretty sure it’s not that. Found the main control failing and can’t find the replacement available through my vendor. Do you guys have it? I’ll just buy from you if so. Thanks for the help on a weekend!

Thought the ignitor was bad but just found the grounding screw loose and in turn the ignitor not tightened down. It lit when I left but want to get the ignitor part number in case I do need to go back on this. Thanks.