Appliance Type: Stove / Oven / Cooktop

Have a kitchenaid wall oven. Model KEBS107SSS04
Error code says to replace the ( UI ), I assume this means USER INTERFACE.
touch pad and pc display board. Neither are identified as a UI and both are costly.

the touch pad display went blank on our 10 year old oven during the night. Time does not show. No touchpad selections work except to turn on the oven light. Every few hours the oven will beep several times on it’s own. Only once however, did the error codes appear. When we try to use the various touchpad features, we get either one or several beeps, but nothing shows on the touchpad screen. I turned off the circuit breaker for 10 minutes and then turned it back on; no change. What do the error codes mean, and how can this matter be fixed?

Eastoriver

hotpoint oven the oven and broiler not working

I have this IN WALL OVEN with an F7 E6 ERROR
From what I read it says control panel problem, I think it’s a membrane that has gone bad
But I can’t find a part number for that… anybody have a clue?

Electrolux range today, According to tech it was built by Dacor. We were transferred to Dacor and sat on hold about 15 mins and never got an answer. The customer complaint is with the racks removed he sets the unit into self clean and the light showing “remove racks” stays lit, the door won’t lock and go into self clean. With the rack rails also removed the rack switch does click like it’s working. Any advice sure would be appreciated.

I have a frigidaire double oven. I went to clean it and got an f8 error. I hit clear and the error went away but I can’t do anything with my oven. I turned off the breaker to the oven and let it sit. Turned it back on and the oven says locked, but it is not and it wont do anything

My name is Roland,
Question: I am working on a Kitchen Aid dual fuel gas range MD# KDRU7893VSS03 SN:DB1375935. The issue with this unit is there’s an error code which says NTC out of Range. I have tested all fuses in the back of this unit, I have changed the sensor -W1076760, the boiler assy -9758598, the appliance manager-w10339702. Still when power up, it goes into lock out with NTC out of range, call for service.
Can anyone help with this issue please. I await your response.
Roland

I have a Kitchen Aid wall oven, electric heat. Model # KEBS107DAL4 – gives fault code:
F3 – E2 ( Oven too hot Replace oven temperature sensor)
This fault code only when self-cleaning. Bake and Broil works fine.
Wouldn’t the sensor fail for baking as well? Thanks in advance for any help.

Randomly beeps “error L43 relay” when not being run. Checked both upper oven power relay and lower oven relay but no visible damage and the error doesn’t always come up only every couple hours a breaker reset fixes it temporarily. Would this be the lower oven relay? I need the diagnostic manual BUT MORE IMPORTANTLY an answer to which board it is?

Hello,
I am trying to install a new oven control board in a Bosh wall mount oven. I get the control panel off just fine, the problem is getting the silver cover off. I removed the knobs no luck, I tried prying it off didn’t work. The only thing I see are the tabs in each corner, I tried to move those as well no luck. The screws that hold the board in place are put in from the front so I know this has to come off somehow just don’t know how.
Any help would be greatly appreciated.

Thank you,
Greg

Robert Dennis

Recently I fixed 2 oven ignitors in 2 different model of ovens. What I noticed was this: they both looked similar, but the one purchased at Home Depot looked like it was made cheaper. The ignitor rod was thinner… With the better built ignitor all I did was take a fine emery cloth sand paper, clean it off, and it worked just fine. I tried that with the other one and I had to replace it. Here’s my question. Could I have replaced the cheaper made ignitor with the better built one? My thought was that the better built one just needed cleaning, whereas the cheaper one had to be replaced. Perhaps I could save my customer some money, installing the better built one..
Thanks

Hello,

When you open bottom oven door the display says bad line then the clock appears then the display goes blank…

We have this cooktop and it is giving a f122.Anyone know what this could be?

This customer had used the oven for about four hours earlier in the day. The oven was off and the bake element shorted out. I know there is always 110v volts to one side of the element. Is it common for an element to short out on it’s own when not in use? Customer is worried that there may be something wrong with the control board. I replaced the bake element and checked for power from the board. The only power present is on the one side coming from the terminal block. Control turns the element on and off with no problems. Control board has no visible problems and is working fine. Is there any concern here? Thank you in advance.

G E range # JGS968SEK1SS ordered a new control board, installed now the range has a code LOC REF unplugged range powers up LOC REF
2 seconds than all the led lights on board on for 15 seconds, than LOC REF appears again cannot clear, can someone help me with issue.

Over heating condition, Burner does not come back on in Sabbath mode.

I replaced the door hinges on the oven about 4 weeks ago. Door was not closing all the way. New hinges worked great until a call back yesterday. This is not the first Jenn Air oven I have had this issue with. . Thank you for any advice.

The door is not locked however I’m still getting this message.
It happened once before we unplugged it and it worked fine now however we unplug it we get the power failure message and then F5 E7

I spilled water on my cook top and not not working now. How can I fix this?

f3 e2 error when you use the micro I replaced the erc because there was no display now I get this code and I already checked sensor I was thinking about installing another erc

Need to replace the relay board (mounted on the underside of the cooktop) and the clock (oven control) on this unit. Parts 92028 & 62790. What is the best plan to get at these to replace ?

We have a Dacor wall oven that was giving an F1 code within seconds of being powered up.
That is a relay circuit failure.
We replaced the relay board and the oven tested ok in the AM.
Customer called said it was fine till after 8pm that night then started beeping and giving the F1 code again.
Any advice sure would be appreciated.