Brand: Whirlpool

I went trough the diagnostic mode and ran a few tests. In the diagnostic mode it starts up normally, fills with water, empties water and spins normally at a slow/medium speed. The error codes that show are F1 E2 which from what I have read is a problem with the Drive motor or Main electronic control board. When I go to calibrate it starts to spin for a split second then it comes to sudden stop as if it gets stuck and the lid lock light starts to blink. This all started because when we try to run the washing machine and it would stay in sensing mode with the lid lock flashing while making a loud humming noise. I eventually smelled an electrical burning smell after leaving it in sensing for several minutes. After attempting this again I am noticing that after it goes through the sensing mode a couple of times and it wants to start up but it looks like it gets stuck because it comes to a sudden stop just like it does when its trying to calibrate.

Could this be the drive motor or main electronic control board?

I put the washer in diagnostic mode and then set it to where rinse was selected to calibrate it. It finished with lid locked flashing. I kept going and put it in manual test mode where spin/done where illuminated. I followed that with the diags where wash/spin were illuminated and hit start …it did not spin at all …only made noises. Please advise.

I own an appliance repair company in Texas. I have found the upper rack may disengage from the rails when the
customer pulls the upper rack out to load or unload the dishes
Wheel axle breaks and causes upper rack to fall when pulled out on many of the dishwashers.
Any suggestions would be greatly appreciated thanks in advance James.

i ran a diagnostic test on the washer but do not know how to interpret the codes.
code 1: F: sensing rinse done E: done
Code 2: F: sensing rinse spin done E: rinse spin done
code 3: F: sensing rinse spin done E: done
code 4: F:sensing spin E: done

Can you please tell me what this means….
The washer will not spin (makes the noise like it is spnning, the lock button flashes)

I’ve just tried to use my broiler for the first time, even though I’ve had this oven for awhile already, and it doesn’t work correctly. It seemed to preheat, but then when I put my fish in, and set the timer, it seems to have shut off on it’s own. I started it over, did the same thing. Is cooling down and not staying on even though it says it is.

I ran the diagnostic on my Whirlpool washes I have blinking simultaneously light for FILL, RINSE and Done. What does this mean? Please help. I don’t want to try and open the top to get the tech sheet cause I need to know first what the problem is.

I Have a Whirlpool Gold French Door Refrigerator
M/N:GX5FHDXVB03 S/N:K02386807 purchased on 6/21/2010.
-The Vertical Mullion Rail (Flipper Mullion) is very warm or even hot to the touch.
-The freezer, set on the warmest setting is too cold.
-The refrigerator is not cold enough.
-After the internal controls for the refrigerator and the freezer are both set to off, the unit continues to sound like it is running. This stops only when it is unplugged.
How should I proceed?

I have a Crosley washer. I have searched and searched and cannot find the model number. By appearance, I believe it is a CAW9244XQ4 . When you push the start button, nothing happens.

Here is the timeline of the failure:
– for about 1 week, when you pushed the start button, the light would come on for sensing and it would do nothing. If you held the start button to cancel, and hit start again, it would eventually finish the sensing and wash the load.
– for about 2 weeks, when you pushed the start button, the light would come on for sensing but it would not run. No matter if you cancelled the load or unplugged it, it would never continue on and run.
– currently, nothing happens when you hit the start button. No lights come on.

I saw this video on youtube: https://www.youtube.com/watch?v=RSR1T8IZK28.
When I followed the key sequence, the washer went into diagnostics mode. I could select the same setting in the video, but it did not solve my problem.

How do I get instructions to all the testing and functions in the diagnostics mode?

This second ground wire may have connected somewhere – I’am not sure. I went behind panel to check on ice buildup because the ice was melting and refrigerator not cold. Right now the freezer seems fine with the fan working somewhat but no cool air is entering to refrigerator area. I can certainly use your assistance.

get water but want make ice

Our range is beeping non-stop and flashing the aforementioned error code. From what I could find online, this is a shorted keypad. So what part do I need and is there a video that could show me how? I really don’t want to have to get a new range and am hoping this won’t be too difficult.