1 vote
3k views

I had a customer today. He had a Genaire gas range. We determined that it was the keypad assembly that was bad. There was an F1 E1 error code. We ordered a new keypad assembly. But while I was there I was looking to see how easy or difficult it was to install the new one.

  • Guest asked 10 years ago
  • last active 10 years ago
1 vote
3k views

The water dispenser inside the refrigerator cabinet broke and when the cup is placed on it doesn’t make contact to dispense water. How can this be fixed if it’s inside the cabinet? Remember I’m talking about the dispenser that’s inside the fridge

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

We are servicing a GE dryer that the display won’t turn on. When dryer door is opend the light bulb turns on so there is electricity. Any ideas of what could case the display not to turn on?

  • mytechjoe asked 10 years ago
  • last active 10 years ago
1 vote
3k views

Is there a way to run a diagnostic test on this unit? The Tech sheet is very basic wiring diagram only. I need to verify if I am on the right track.

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

Is there a video on how to replace this particular ice maker: 00675261?

  • mytechjoe asked 10 years ago
  • last active 10 years ago
0 votes
9k views

My Bosch dishwasher is not working properly.

0 votes
3k views

My Kenmore dryer is making a squeaking/grinding noise.

0 votes
3k views

My Whirlpool refrigerator is not producing ice.

0 votes
2k views

Can set cycle but will not start. Main board clicks but no start. Is there a thermal fuse in the air flow I don’t see.

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

Customer complaining giving error code with heavy load

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

When you select a cycle and push the start button I can hear the relay on main board click but dryer does not start. No fault codes come up. Is there a thermal fuse that cuts out the motor. I did not see one in the air flow.

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

My Whirlpool refrigerator is not cooling properly.

0 votes
6k views

My Dishwasher is displaying a AE6 error code.

0 votes
3k views

My Samsung dishwasher will not start.

0 votes
3k views

The tub will not spin in my Maytag washer.

0 votes
3k views

I have an issue with a Oven, it’s a Kenmore and this is the problem I am seeing: Door not properly closing

0 votes
3k views

My Dryer is taking too long to dry my clothes.

0 votes
2k views

My Samsung refrigerator is not cooling properly in the freezer section.

0 votes
3k views

The fan in my Maytag refrigerator is not running.

0 votes
3k views

My defrost heater is not testing out properly.

0 votes
2k views

My refrigerator is not making ice.

0 votes
3k views

The panel is cracked on my Maytag dryer.

0 votes
3k views

One of the drawers in my Samsung refrigerator seems warmer than it should be.

0 votes
3k views

The dryer knob on my Samsung unit is not secure.

0 votes
2k views

GOOD MORNING. I FOUND THE DRAIN SOLINOID JAMMED UP WITH MELTED PLASTIC. I USED MY METER TO CHECK FOR 110V AT THE SOLIANOID , BUT DID NOT GET IT AT THE DRAIN CYCLE. ALSO, THE MOTOR WAS NOT GETTING 110V AT THE DRAIN CYCLE. I TRACED THE WIRES UP TO THE CONTROL TIMER AND ALL LOOKED IN GOOD CONDITION. I PULLED APART THE TIMER AND ALL THE CONTACTS LOOKED OK. ANY HELP WOULD BE GREAT. THANKS, TODD FROM NY.

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
6k views

induction burners not working when two or more burners are being used at the same time, ordered pcb inverter assembly # dg94-00728a . needs to know how to disassemble top to replace inverter assembly.

  • joeski1369 asked 10 years ago
  • last active 10 years ago
0 votes
3k views

sounds like a freight train when spinning

  • joeski1369 asked 10 years ago
  • last active 10 years ago
0 votes
14k views
  • Guest asked 10 years ago
  • last active 10 years ago
-1 votes
3k views

troubleshooting tests

  • Guest asked 10 years ago
  • last active 10 years ago
1 vote
3k views
  • Guest asked 10 years ago
  • last active 10 years ago
Showing 5581 - 5610 of 9k results