Search result: W10237498 BRACE, TRANSPORT

No videos found

We were unable to find a video for your search query. Please try again.

Looking for a video by Model Number?

We've entered your search below, please click search to search our Model Number Lookup.

Find your answer on Repair Help

Have a Question about a Repair?

0 votes
72 views

Can you send me a video on how to replace a spider bracket for a front load wahser?

0 votes
181 views

Machine does not complete cycle – no spin

  • kmisch asked 4 weeks ago
  • last active 4 weeks ago
0 votes
120 views

Problem when spinning make a lot noise whirlpool washer

0 votes
114 views

Please me help

0 votes
114 views

Customer complaint before arrival is washer will not spin the clothes out at the end of the cycle. Homeowner did advise that it will only work on bulky cycle technician arrived. Had an F5 E2 code door lock assembly error. We replace that unit is still not spinning out on any other cycle, except for bulky, when we came back out, we went to retrieve the error codes and there was none in there ran a cycle on normal and it does not spin out the clothes. You can turn it to drain and spin and it will spin out the clothes properly also, the drain is working properly too , not quite sure where to go with this any help would be appreciated Please email me if you need more information or need anything. Thank you, Daniel Woods.

  • dwoods asked 1 month ago
  • last active 1 month ago
0 votes
197 views

washer is not draining, but I just replaced the pump 2 yrs ago, the pump seems to have proper resistance, touching it through the filter hole.
I recall the flapper can be a problem , it’s a rubber check valve . Is it possible a hot steam cycle made is flexible enough to push through and cause problems with all cycles? it started on steam cycle, now all cycles won’t drain. I thought i would ask you guys before I go to the trouble on this .

also I know your 29.00 only co=vers one appliance , but I just need a recommendation, matching dryer dv448gp/xaa is a bit noisy, do you guys recommend replacing the springs and wheels around the drum, or should I wait till some happens?

  • Bluewasher asked 2 months ago
  • last active 1 month ago
0 votes
189 views

I have a service call tomorrow for a refrigerator not dispensing ice. It does dispense water, icemaker is making ice the only issue customer said is not dispensing ice.

0 votes
264 views
  • birdman asked 3 months ago
  • last active 3 months ago
0 votes
268 views
0 votes
239 views

Not spining

0 votes
275 views

It had the compressor replaced about 3 years ago, I can fill it running but my gauges won’t work I guess it is because it is a flamable refrigerant. the condensor and evaporator fans are running. I replaced the thermister on the compressor but it didn’t help Idon’t know how to test the other components. It has a small computer on the top but I couldn’t find a way to test the other components.

  • birdman asked 4 months ago
  • last active 4 months ago
0 votes
329 views

My technician changed two infinite switches on a radiant cooktop.

The part that was changed is 700855K. Issue is that the two right side burners, after connection, control each other’s heat level. Burners turn on independently and the issue with heat control is only applicable if both burners are operating simultaneously.

Could you provide guidance on proper wiring instructions for these switches? My thought is that the technician did the wiring incorrectly. The old switch for reference is part# 203147. The confusion lies in a difference for terminal markings between the old switch (203147) and new switch (700855K).

I’m the owner, but not a technician. Please let me know if there is a bulletin or supporting document for the issue.

Thank you,
Greg Bahry
832-656-9034

  • gregoryb7 asked 4 months ago
  • last active 4 months ago
0 votes
355 views

I have a 10 Year old Speed Queen dryer. I watched your video for replacing the timer a D517560 but my dryer does not have the connectors it just has the separate wires with the little clips on the end. Where do the 2 black wires from – it looks like the timer go. One goes to the T connector but I need to know where the other one terminates.

1 vote
270 views

watched your video, ordered a new capacitor and relay module. Installed new unit same issue. Any other solutions? Refrigerator is only 13 months old.

  • twobe1 asked 4 months ago
  • last active 4 months ago
0 votes
256 views

Refrigerator is cooling ok but freezer is 51 f

  • Juancarlos asked 4 months ago
  • last active 4 months ago
0 votes
258 views

The condenser for this combo needs to be changed due to moisture not being removed. I would like to know if there are any videos for this model as its a never version. Need any tips on assembly for this part.

  • GeekJames asked 4 months ago
  • last active 4 months ago
0 votes
284 views

Wondering does the air flow Tower need to be changed or just the evaporator fan motor. Is there another motor that needs to be changed as the condenser fan motor is spinning and working in the back of the refrigerator. Just checking to ensure this refrigerator only has one evaporator fan as it seems just to send the air through the air flow Tower

  • GeekJames asked 4 months ago
  • last active 4 months ago
0 votes
308 views

My Samsung refrigerator model #RF263TEAESR/AA is leaking water and pooling under the deli tray and even had some ice on it. So I unplugged the appliance and let it defrost then took it apart as as Appliance Video.com instructed. I disconnected the wires on the top right as the video showed and removed the thermostat wire and sensor. Then the video directed me to the left side. There is a connection for the defrost heating element and I only unplugged that. The video instructed me to then remove the bi-metal however, my refrigerator does not have a bimetal. It has the plug but it just loops back into itself with a red wire. Does this mean that it has no need of a bi-metal anywhere? my refrigerator has the numbers 07 in the corner of the data tag if this helps.

Thank you,
Jack

0 votes
308 views

Washer give a cancel error on heavy bedding loads. What could be the cause of this?

  • GeekJames asked 5 months ago
  • last active 5 months ago
0 votes
344 views
0 votes
314 views

Blomberg dryer is not heating. Is the heater not receiving enough current?

  • SiNRG asked 5 months ago
  • last active 5 months ago
1 vote
291 views

This icemaker won’t make ice. It fills but doesn’t harvest cubes.

  • Pancakes asked 5 months ago
  • last active 5 months ago
0 votes
435 views

How to uninstall water filter housing for this model.

  • GeekJames asked 5 months ago
  • last active 5 months ago
0 votes
428 views

I need to know how to remove the water filter housing RFID board. Board has a small bolt screw not sure what size tool needed to remove. Any videos, service manual and tools used to perform repair would be greatly appreciated.

  • GeekJames asked 5 months ago
  • last active 5 months ago
0 votes
407 views

The leak is coming from the water valve into the fridge. I tested the valve: 185 ohms. I also tested it mechanically thinking it would stay open but it didnt. Could this issue be with the ice maker or mainboard. I dont know how common this fail is with this refrigerator.

  • SiNRG asked 5 months ago
  • last active 5 months ago
0 votes
328 views

We have replaced the main control board on this unit. The code “UR” is popping up no matter the size of the load. Small or Large.

0 votes
323 views

I need to replace defective PCB board

  • Loinest76 asked 6 months ago
  • last active 6 months ago
0 votes
285 views
1 vote
395 views

Freezer section is at room temp. The condenser fan is running, the evaporator fan is not. The door switches are working. Im not sure about the defrost timer. I turned it over about 5 times and nothing happened. There is no tech sheet. Can the timer or terminator stop the compressor from running?

  • SiNRG asked 7 months ago
  • last active 7 months ago
0 votes
382 views

What are the reasons the capacitor keeps blowing? And how do you test them? The motor runs, the agitator moves freely and so does the drum. The drain pump is clear.

  • SiNRG asked 7 months ago
  • last active 7 months ago
Showing 1 - 30 of 9k results
Our Senior Technicians are here to help!