Appliance Type: Dishwasher

Wasn’t sure if there was a problem with a part or maybe something stuck? Having my husband take a look but not sure where he should start.

It goes through every cycle but the one we need, the wash!

Not sure what’s happened to our dishwasher door, it seems to not really ease open like it used to.

Why do my dishes seem to not get completely dry like my older model I had for years? Really bugging me that I have to hand dry some items even after a “heat dry” is on.

hello

I have a kitchenaid dishwasher that starts to fill and stops before it reaches the float. the float moves freely and the float switch itself is good and electically works

any idea where to go next

thanks
james

I own an appliance repair company in Texas. I have found the upper rack may disengage from the rails when the
customer pulls the upper rack out to load or unload the dishes
Wheel axle breaks and causes upper rack to fall when pulled out on many of the dishwashers.
Any suggestions would be greatly appreciated thanks in advance James.

I think it’s a thermal fuse that I’ve narrowed down but couldn’t find a video on actually replacing it or if I need more than that. Any help would be great.

Can I just fix or adhere the existing seal in place or will I have to replace the entire thing? Couldn’t find a video for my model#. Thanks.

This is actually a series made by Whirlpool 810-811. The motor is not running and water doesn’t drain. However, the board will still go thru its cycles as if it is working properly. Is there a reset button somewhere on this unit to start the motor? This is a 12 year unit which I’ve probably used half a dozen times.

What recommendations can you provide as I’m a DIY’er?

bosch dishwasher model she6at05ucx/o5
error cod e64
we replaced the control board to no avail
need some assitance please we belieive it could be heating system , also
how do you get this dishwasher into test mode

Complaint: Unit taking very long time to complete cycle and or pauses with water,
but will complete cycle. This unit is located in a Seminary with multiple users so can’t get proper feedback. Any help appreciated.

Can someone share with me what function the Turbidity sensor performs in a dishwasher.

Clean light blinks 7 times. I have no idea what this means. A Tech Sheet would be greatly appreciated. There is not one with the DW.
Turning off the power to the DW does not reset the light. Thank you.

I have a E01 error code on a Ascenta Dishwasher? any suggestions

What can I do to change that? Or is it not possible? Just doesn’t seem to be the same and I’m not sure if it’s a good thing.

I was advised to switch the button control units as the top drawer selector will not move from rinse.
How do I access those controls? Is there a walk through? Diagram?
Do I need a serviceman yet??

I can’t select cycles or adjust it using any of the buttons, sometimes it lights up, other times it won’t come on at all. Is this something my husband could fix? Appliance shopping is the last thing I want to do right now.

I saw the videos on clearing the chopper and sump area, and I checked the pump as well. I removed some debris thinking I’d solved it, but same thing happened on next load. Not sure where to go from here.

How do we replace the two tracks that hold the upper rack? Is there a video that shows this? Ours does not have visible screws. Please advise. If you have a video, we would definitely subscribe to watch that video.

I’ve noticed that the top drawer fills with water slowly after a wash cycle. The bottom drawer is fine. If I don’t run it for a while, the water continues to fill. I’ve read that it could either be the water inlet valve or the drainage hose. I believe that the drainage hose is positioned high enough with a loop such that water can’t come back in.
In my debug mode, I’ve since shut off the water source into the dishwasher and I’m hoping to wait a few days to see if the top drawer continues to fill up.
Are there any other tips that might be useful? (I’ve watched the YouTube video for repair of the inlet valve).
Are there other troubleshooting things that I can do to narrow in on the problem?

Thanks,
Jon

The wash program selector is stuck on “Rinse” and will not move.

Start button does not work.

drawer lid works intermittantly. had the lower replaced 6 months ago for same issue

Our dishwasher wouldn’t finish the rinse cycle and the lights just keep blinking. I tried canceling and draining but it seems completely unresponsive. Can I reset it somehow or try to restart it? I’d like to have it working, especially over the holidays.

We have had our Maytag dishwasher for a few years. The door will not open. The latch seems lose and it you try to open it, the latch get pushed up and jammed. Is there a way to open the door so I can check the latch?

Our dishwasher comes on, lights up, and fills, but then won’t actually wash. It just stops and there’s almost a low hum noise. My husband got it to cancel and drain and I redid it thinking it was a fluke, but exact same thing happened. What should we do from here?

My research leads me to believe that it is the actuator. agree? and if so, I’m not finding a video.

Dishwasher won’t start. Panel lights work. I press (Normal Wash), (Heat Dry) and (Start/Resume).

1) I can hear water softly running.

2) After a minute or so, I hear a 1 second long buzz that repeats every 5 seconds for a half a minute or so.

3) Then the cancel/drain light comes on solid. And, water is draining into the garbage disposal.

4) After 30 seconds or so, all the lights go out.

I reset everything by shutting off the circuit breaker. No change.

I think maybe the Float mechanism or switch is bad, so I remove the float and everything is very clean and free. I remove the switch and check it with a meter and it is fine.

So, what do I do now? Could it be anything else other than the control board?

Our dishwasher hasn’t been very effective, and I thought it was a bad chopper assembly, so I changed that out, but it’s still not working as well as I’d like. What else can I check?