Appliance Type: Dishwasher

Dishwasher leaking by bottom corners of door
How do I fix this?

When I first arrived the lock led was flashing like the control was locked. I cleared it but it still would not respond. Then the heated dry began flashing.
Is this a problem with a stuck pad?
What else could it be?
I need a tech sheet and service manual.

My dishwasher was leaving dishes filthy and my silverware stained. I disassembled the dw to find the source (turns out it was a horrible p-trap plumbing job, corroded disposal, backup, etc.
Unfortunately, I violated my own rule of appliance repair, which is to photograph every step in the disassembly. When I went to reassemble, I followed the parts diagrams, only to discover GE either poorly represented the positioning of the parts or it completely omitted key parts. I then rented your video on installing the flood switch, but that did not describe what screw I was supposed to be using.

I’ve narrowed it down to (I hope) one or both of the following problems:
1. The screw holding the flood switch housing in place: what is it? (part number/size?) (GE has no reference at all to this screw in the parts diagrams). I wonder if I might be using the wrong screw? I don’t have extra screws and I believe every screw is in the right place. Maybe it’s too loose? How tight is it supposed to be?
2. The float stem O-ring. I cannot tell from the diagram where this o-ring is supposed to go. Right now, it is on the float stem, at the narrow part that inserts into the base of the sump manifold. I think it’s doing what it’s supposed to do, (with the exception of the leaky screw below it), but I’m unsure, because I can’t rule out that’s it’s positioned improperly without fixing the leaky screw.
3. Oh, yeah, well, there’s this too: when I was removing the electrical circuit board to replace the electrical cord, I broke off the little white tab on the connector clip for the Flood switch harness assembly. When I reassembled it, the board, I googled a lot of “electrical connector clips for circuit board,” etc. with no luck. Right now it’s taped into its proper place in the board, but wonder if that might not be helping things…

I appreciate your help!

I bought a brand new in the box dishwasher that was 2 years old. I plugged it in and it didn’t clean very well. I tried all of the cycles and still not clean well. I checked the water input to the water inlet valve and it was strong. I then pulled the hose from the water inlet valve to the inlet assembly and it seemed strong. I did notice that when I run a cycle the arms never move. There does seem to be water in the dishwasher and it drains just fine. I tried adding a couple of quarts of water to the bottom of the dishwasher to see if not enough water and still the arms didn’t seem to spin. I bought your video on diagnostic modes and when I run it I received the following codes before the test happens. If it were new from the store I could ask whirlpool but since I bought it second hand, even if it was new in box, I can’t,

F4 E3
F4 E3
F6 E4
F- E-
F- E-

The dishwasher stopped cleaning. I determined it was not filling with water. I found the screen on the inlet valve was plugged. I removed it and cleaned it out. It now fills with water but when it gets to what would be the wash cycle it just sits for a few minutes and then goes to the drain cycle. I have unhooked the power to reset it and still has the same problem. I also added more water to it to make sure it wasn’t a water level issue and it still will not go to the wash cycle.

Hello, the dishwasher is leaking during cycle on the bottom left side of door, there is a small black plastic flap? About 6 inches in length is the location where it drips from.
I don’t know if the leak is relative, but my dishes aren’t drying either, there is still water on dishes and such after the “Quick and Dry” cycle has completed???

Unit has no power. What do I look for and if it is the timer how do I test the timer.

I am getting a 6C3 error code on my dishwasher. Also it will not do anything.

I am getting a 5C error on my dishwasher. Also has water in the bottom that wont drain.

My dishwasher is displaying a 7E error code.

My dishwasher will not start also getting 4E5 error code.

AE6 error code on my dishwasher.

When I press the start button and close the door, the dishwasher will not start. Then there is a yellow flashing light on the outside of the door and a beeping sound until I depress the start button to shut the dishwasher off. What part do I need to repair this machine?

This dishwasher keep draining no matter the cycle. The unit will not fill up with water at all to actually wash the dishes.

I am getting a 9C1 error on my samsung dishwasher.

Dishwasher will not drain. SC error code.

My Samsung dishwasher will not run and is displaying “LC” error code.

My Samsung dishwasher is displaying an FC error code.

My Samsung dishwasher will not run. AE6 error code.

My dishwasher is reading a CE error code.

My Samsung dishwasher will not run.

My dishwasher buttons are not working. I am getting bE error code.