Appliance Type: Stove / Oven / Cooktop

This is built in microwave/oven combo, and I’m looking at a bad control. Are they still available? And do you guys carry them?

Checked the element, probe, thermostat, and then found that the control is bad. Seems like a high cost for the control and if I add in my fees, it far exceeds a reasonable repair price. Should I just advise to buy new?

Question on this range .The complaint is the temperature doesn’t rise above 180 degrees.
Technician came out he found in both bake and broil cycle part is on
the electric element just below the broiler burner . We are not familiar with this type of range. We will really appreciate any input.

This unit keeps coming up with a door lock error and you can’t even get inside the oven to use it. I think the entire door latch assembly needs replaced but I have no way to lookup the parts information currently. Can you help me on this?

Trying to do a lookup and my usual sites aren’t working, need the igniter part for this unit. Current one is not lighting at all anymore. Appreciate you guys always being willing to help me out!

Hello,
I am trying to install a new oven control board in a Bosh wall mount oven. I get the control panel off just fine, the problem is getting the silver cover off. I removed the knobs no luck, I tried prying it off didn’t work. The only thing I see are the tabs in each corner, I tried to move those as well no luck. The screws that hold the board in place are put in from the front so I know this has to come off somehow just don’t know how.
Any help would be greatly appreciated.

Thank you,
Greg

i have looked at ignite-rs they are good both boards have been replaced so i know it is not the board I’m at a lose as to what it could be please help thank you.

I have an Electrolux Gas Oven M# EI30GS55JS – and the clock display does not light up the “1” for times 10:00, 11:00 or 12:00. It only displays the last 3 digits. example is the display looks like 1:00 when it should be 11:00.
The parts diagram shows a glass cover and a separate control board. All functions for the oven work fine. I think I need to order the glass cover(part#318923502) or the control board (part# 316576703)?

All four burners are turning on when the left front burner is lit. I changed out that switch but there’s still an issue with them all coming on. What’s the deal?

you replied to me yesterday that you had no video for this model of gas range is there a manual or written instructions that I can look at, thank you

DCS WOT-230 only heating to 265 degrees on top oven bottom ok, remove oven check elements, stats, all wiring connections, top sensor and lower sensor was a little different in ohms, so swapped them now top oven heats to 320 only when set for 350, lower oven still works fine, I thinking that the MCB is bad, anyone have any experience with this issue?

Electrolux range today, According to tech it was built by Dacor. We were transferred to Dacor and sat on hold about 15 mins and never got an answer. The customer complaint is with the racks removed he sets the unit into self clean and the light showing “remove racks” stays lit, the door won’t lock and go into self clean. With the rack rails also removed the rack switch does click like it’s working. Any advice sure would be appreciated.

Would this just be a knob issue? I have checked out everything else and it looks fine.

The customer can’t use the oven, but I’m also having trouble finding this replacement part available from my usual vendors. I noticed you didn’t either. Is it a DG66-00017A? At least want to confirm that.

Another Dacor Wall oven.
Upper oven would no heat, lower oven working fine.
This is a double oven electric. Upper oven would not heat. no power to the element. visual inspection on PCB relay shows the the relay is burnt. put in new board and now “F4” fault shows for both top and bottom ovens. Put in old board and F4 still shows for both ovens.
Trying to avoid having to remove the oven. No wiring diagram. It appears that the oven sensor (upper oven) was replaced some time ago (because of the wire nuts). What is throwing me is that the bottom was working and the only thing that changed was the board and when I returned it to its original state – the bottom is not working.

Any help is greatly appreciated.

I think I just need two of these burner knobs. Do you guys know the availability and pricing on them?

I have need of the part number for the small fuse link that is on the back wire to the control. It has Two fairly large spade terminals at either end. I cannot see it listed on the schematic. Can anyone assist?

Dacor Wall oven. Upper oven would no heat, lower oven working fine.
Double oven electric. Upper oven would not heat. no power to the element. visual inspection on PCB relay shows the the relay is burnt. put in new board and now “F4” fault shows for both top and bottom ovens. Put in old board and F4 still shows for both ovens.
Trying to avoid having to remove the oven. No wiring diagram. It appears that the oven sensor (upper oven) was replaced some time ago (because of the wire nuts). What is throwing me is that the bottom was working and the only thing that changed was the board and when I returned it to its original state – the bottom is not working.

Any help is greatly appreciated.

I have a Kitchen Aid wall oven, electric heat. Model # KEBS107DAL4 – gives fault code:
F3 – E2 ( Oven too hot Replace oven temperature sensor)
This fault code only when self-cleaning. Bake and Broil works fine.
Wouldn’t the sensor fail for baking as well? Thanks in advance for any help.

Looking for two Thermador hinges part # 00488417
Any help would be appreciated

This unit is not reaching pre heat or even maintaining any temperatures. Checked all the heating components and they are fine. Got to main relay board and found it bad, cannot find it in stock through my vendors, do you guys have it?

I checked the control it seems ok, so I’m assuming it’s the touchpad. Do you guys have some part information there you could pass along for this? Thanks.

This needs a touchpad but I can’t find the part lookup information for it. Thanks.

I don’t have a model number on this oven. I was working in this kitchen removed the oven door improperly and could not reinstall it. I pushed the hinges and set the catches and attempted to put the door back on. After a little effort I got it back on but then could not open it. The door is locked. I have tried a coat hanger to pull on the lock without success. I have tried setting self clean and then cancelling it and turning off the circuit breaker for a few minutes. I would be very greatful for any tips on how to get the door open. Thanks

—

Does this come with some kind of kit for the entire assembly? I think I need the valve and knob for it. Thanks for any information you can get me.

When customer programs MW say for 60 seconds, it starts counting down 59 58 57 56 55 . When that happens, it quits heating and shuts off. He will cancel, and after a few seconds of heating and counting down, it stops heating and the count down just stays there.

Have a kitchenaid wall oven. Model KEBS107SSS04
Error code says to replace the ( UI ), I assume this means USER INTERFACE.
touch pad and pc display board. Neither are identified as a UI and both are costly.