Repair Help

A high pitch whine or scrapping sound coming from the vent hood when in use may be caused
by the rubbing of the blower wheel. To repair, use part number WB26X29333 motor assembly
kit.

Consumer may be concerned with uneven grates or grates not aligned to control panel.
A gasket was being installed in the wrong area. This resulted in the pan unit (drip pan) being
uneven, which in turn impacted the grates

My washer moves around a lot.

My dryer stops running in mid cycle

My washer is vibrating a lot and walking across the floor.

My GE washer is not draining all the water out.

After the cycle the dishes are still coming out wet.

My dishwasher will not do anything.

Hi, I have tested the grid on the ice machine and this is ok with continuity all round the grid but no heat is being generated to cut the ice. What other problems could be causing the grid not to heat up.

Cannot get board to power up.

Bake and Broil shut down when temperature
reaches approximately 250F. How do I correct this ?

Surface elements will not work and the light ring around the knobs will not illuminate.

Ice or Frost Formation Around Ice Box Door Opening

If the door of either the fridge or freezer is left open for more than about 20 minutes, the freezer and fridge temp then creeps up, with the fridge ending up in the mid 60s, and neither will cool down. If the entire unit is turned off for about 24 hours, alot of water ends up in the pan below (this may have nothing to do with problem–just noting it). Then power up and it will return to normal operations.

Sometimes this problem shows up even if no one leaves the fridge or freezer door open, but usually that’s what it takes.

No strange noises. All the fan intakes are clean.

The unit is showing me a R10a code that the ice maker sensor is open or shorted. But all the tests are fine for the Ice maker sensor. the temper and ohms correspond to the chart and the dc voltage is 3.0 at 39000 ohms. The ice is forming on the inside of the refrigerator corresponding to the position of the air passage from the freezer to the ice room in the refrigerator. That is also where the water under the pantry drawer is coming and not the fresh food evaporator drain. It said in a manual for another samsung to check the thermister reading at the display but I don’t see any information how to program it to show that or any thermistor temperature except the normal operation readings of the actual temperatures. Isn’t there some way to run the damper and lights and evaporator fans ect……? Is there a better service manual for this and if you have ever seen this kind of freezing in the air passage, what did you do?

The ice maker fill tube in the back of the freezer, freezes after making a cycle or two of ice cubes.

Costumer says Oven randomly shuts off while baking. I saw it shut off once after shutting it off every couple minutes and then restarting it so I never got to 350 even though that’s what it was said to but it randomly shut off after two minutes of running. I replace the DSI ignition module for the oven but the customer is saying that I did it again where it was getting significantly less warm in the oven in the oven just shut off. Can you guys please provide me with a wiring diagram and your technical input on what else could be regulating the system? I’m thinking that electronic thermostat that I saw there I would appreciate your guys input.

The top elements work fine, but when oven turns on house breaker trips

dryer not heating , changed thermal fuse DC47-00016A worked hour later customer called no working agian .

My question is what would cause the F30 error code to come up I did a preliminary search and found it had something to do with the oven probe or the main control board I tested the resistance of the oven probe and had 1.097K which looks to be correct . The manuals that I downloaded off the Frigidaire site did not have anything corresponding or any information on error codes .
I would like to confirm that the main control board needs to be replaced after checking the probe if that is what the F30 error code means

I just installed a new motor, and a gear case. I followed the calibrating instructions that came with this parts. unfortunately, this machine did not claibrate. currently I try to wash some clothes on it, it just goes through the circle, without properly washing the cloth. clothes not clean. need help……

The hose that comes out of the refrigerator goes behind the compressor to the front of the refrigerator. Can this hose be replace on a GE Profile refrigerator?

I need a service manual so I can pull up error codes. Any videos on this?

The tech sheet is missing . Any videos on this code also