Repair Help

Please help on error code F8E0

what dose it mean and how can we fix it

removing dryer motor and fly wheel without breaking the fly wheel during the process

This microwave will shut off mid cycle. The control will stay completely blank and nothing will happen. If you leave it unplugged for a little while it will cut back on and functional normal for a few cycles. Is the the control board going bad, or is it the mag tube interfering with the board and shutting it down. Are there any test I can do to check this, as everytime I am there after I plug unit up it will work fine for many back to back cycles

So originally if compressor is The Refrigerator in the freezer were extremely extremely hot and they both were not working properly I cleaned out the condenser coils and I’ve recommended that they shut the machine off for some period of time to cool the compressor is off they have done that.
Now after doing that the refrigerator compressor is working fine however the freezer section is only Cooling as if it is a refrigerator also they have mentioned that the compressor is making noise I do see that someone has replaced the start relay on the compressor with a 3in1 before I go back there I would like to know what the temperature the high and the low and how to check it on the compressor should be and how to refill it with Freon if it needs

so i put in into diagnostics mode and i got an error of F6 E1
how can i repair this?
its a Kenmore washer

Hello
Found a GE side by side with duel evaporator, the problem is that it Is not cooling in the fresh food section. Upon taking out crispers noticed there is 3inches of frost going all the way around this box that covers the evaporator. This unit does not have a defrost system, what should we be looking for? We have not run into this issue before.
Thanks

  I went out on service call on a Kenmore bottom freezer/refrigerator. I would like to know how to get the pcb in diagnosis mode. Thanks

How do you remove the basket from the drive unit?

i need a service manual for this beast. I need to know how to adjust the freezer door

We went to service a Samsung fridge that is not cooling on fresh or freezer side. Error code displayed as 22 C but we could not find anything with this error code. Compressor is a bit on the warm side but not hot and it does turn on. Evaporator and fan look good as well. Please advise.

I am not getting any power to the fan or compressor.
I disconnected the plug that leads from the power source to the box below the door switch.
there is power going into the box but not going out of it meaning supplying the compressor and fan ect

Initial problem was that refrigerator wasn’t cooling. Main control board and powersupply was replaced. A month later customer calls that refrigerator is not cooling again and now is making a loud noise. Any suggestions?

We have gone four times to repair this microwave. The customer complains that the microwave does not heat. Initially we replaced the magnetron and it was working. On the second visit we replaced the thermal fuse. On the third visit it was heating but a reset was done aswell as reconected wires to thermal fuse and unit was heating. On the fourth visit the unit was heating but a reset was done again. Now the customer calls is complaing that it is not defrosting and heating, any suggestions?

the freezer is not cooling and has made ice in some time
the fridge is not cooling.
i check the condenser fan it is running but both composers are VERY VERY hot.
i did clean the coils but there was not much dirt to be cleaned.
i have also checked the water inlet valve for the ice and it seems fine

Customer says when they close the bottom drawer it might stay closed an day or a week but it opens a little then starts to frost across the top of frz. And the Icemaker frosts over. Do you know if fridgidaire had a issue with this.

THE UNIT HAS 3 ERROR CODES; SUD, F21 AND F35. THERE ISN’T ANY SOAP IN THE MACHINE. THE PUMP IS WORKING AND THERE ARE NO BLOCKAGES. THE TUBE TO THE ANALOG PRESSURE SWITCH IS OPEN.

I GUESS I NEED TO KNOW HOW TO TEST THE ANALOG PRESSURE SWITCH, IF POSSIBLE. ANY OTHER IDEAS WOULD BE APPRECIATED. ALSO IS THERE ANYWAY TO CLEAR ERROR HISTORY ON THIS UNIT?
THERE WAS A MENTION OF CLEARING VENT HOSE, WHERE MIGHT THAT BE, AS I DIDN’T THINK ANY HOSES I COULD SEE WERE VENT HOSES.

THANKS

Hunting tech sheet for above model, found two different ones for GU2400 on psa flash drive. Put in new control lasted about 30 days, replaced & 2nd one lasted about 30 days & failed. Unit does not start & flashes clean 7 times & repeats. Any help will be greatly appreciated.

I was getting an error message sy… and I was told to change the switch board under the front of the unit.
I changed it once it didn’t power up so I thought it was faulty.
so I changed it out for a new one.. I hot the new one and I have the same issue. it just will not power up