Repair Help

need service manual for my samsung refrigerator

I have watched your video on how to replace the ice maker for my refrigerator. I have removed ice tray and the side piece protector for the power cord and have the cord unplugged. Now I have the unit halfway out and cannot get it any further. I have pulled and pulled, is there a secret?
In the video he makes it look so simple.
I don’t know what else to try.
I’m afraid if I strong arm it too much I may do damage to something.

Need service manual

I’ve got an error code E08,03 – short circuit coil, wiring to coil or controller, replace controller

The water seems to be entering the tub okay when I put it into diagnostics, however when I tried to put it into a short cycle diagnostics mode, the dishwasher wouldn’t enter into this diagnostics mode. I’m suspecting a bad control board.

No power on water valve

I replaced the right front burner element and am getting F5 and the right front burner heats up without being turned on.

Clicking noise issue

Fridge is 1 year old

Do you have an option where I might be able to speak to a Technician over the phone?

Oil has lit all over the motor and drive pulley. Oils is on the belt and shifter causing issues with spinning. What parts should I look at replacing to fix this issue. what is causing this issue and how would I go about doing his repair.

Dryer makes high pitch sound when spinning. Roller was changed and it was spinning which out high pitch sound. What part should I look at changing to fix issue

I am training as appliance technician . I tried search box but couldn’t anyway thing.

I have a washer that won’t wash or spin, everything else seems to work, has what I believe are error codes 5, 29, 1, 41, 5, 3, 5, but have no technical data to explain what these are about.

Hello,
The samsung fridge is not cooling or freezing. I found codes 83 and 84 related to the compressor and went ahead and replaced the inverter board. The board light stays on steday and the fan runs on the compressor. I think this indicates normal operation. However its still not cooling or freezing. I don’t know if there are steps to take to reset the fridge. i have left it unplugged for an hour with the hope that it would reset and start to cool. I have also looked again at the error log and nothing new is reported. I ran the self diagnostic 2 fridge sensor error and received a “C” in the response thinking that a temperature sensor might be the problem. These are the parts I considering to replace but want to know if I’m in the right

Temperature sensor (DA32-00029Q)
Thermal fuse assembly (DA47-00301B)

Origonally the double oven had F64 Error code while either oven was on. Both fans working, we changed out the main control board. Now F64 error code after the top oven runs for a minute. The bottom oven works half the time, other half F64 pops up. There is no sell switch in this unit. We then replaced both cooling fans in both the upper and lower oven. Now after a while both ovens are not working and they have the original error code. What do we do next? Customer does not want to replace oven.

On my refrigerator the freezer is cold but the refrigerator is not cooling. Started about a week ago when the freezer was freezing over And the refrigerator and we heard a loud noise like. We were told we needed to unplug the fridge for a few days because the fan was hitting blocks of ice. So we did and now the noise is going but the fridge section will not cool down the freezer section is very cold. Do you have any idea what this could be?

• Samsung Refrigerator mode # RF28R7351SR/AA
  ICE shute opens and closes on its own. The display works fine and you can change between water, crush or cubes. The shute opens and closes repeatedly non stop. Dont know where to begin troubleshooting.
  Thank you

I have a Family Hub Refrigerator with 4 doors. The freezer section (bottom left) no longer freezes. The flex zone (bottom right) now seems to not be cooling as well as it use to (used as a fridge). Fault history shows error 83: Compressor Current & 84: Compressor Motor from about 6 weeks ago. However, those faults do not show anymore when running a self-diagnosis. I receive no errors during a self-diagnosis. I’m. trying to figure out if I should try replacing the PCB inverter board, or if it’s a more serious issue.

I did replace the compressor and evaporator and heat exchanger on the sub zero model 680/s
Everything is running but not compressor,
Please I need advice and seal system service manual .