Appliance Type: Dishwasher

We are not getting any water into the dishwasher. Water lines are hooked up

Water slowly leaks into the dishwasher when it is off. So the bottom of the dishwasher has a pool of water if not in use. There was sediment in the water valve, so I replaced the water valve… but the dishwasher is still leaking slowly while off. What could cause this issue?

I have a kitchen aid stove. I tried to remove the oven door without placing the pins needed. It came off but the hinge came with it. how do I fix it?

Dishwasher door will not close.

On my Maytag dishwasher (mdb7749sab0) the lights don’t come on when I press Start. It won’t start. Happened yesterday and then it worked. Also, it worked again today, but tonight, the problem is back. Press Start and nothing.

I have a Maytag dishwasher that has a red “lock” indicator light that goes on every time i try to set the cycle.

My Jenn Air dishwasher JDB1270AWY has started making a grinding noise during part of the cycle. It is cleaning great and seems to be draining fine. Ideas?

DW80J9945US getting LC error code. Can you please tell me how to diagnose this? Thanks.

what would be causing this, we already changed timer part #: WD21X10201

Some of the buttons on the touchpad of my dishwasher are not responding.

looking for a touch pad 5304470639 frig model PLD4460RECO its built by maytag.

The dishwasher has power. The Hi-scrub light is on. No switches will activate any function. Nothing comes on when the door is closed.

Ran the diagnostics tests and when it was done the light on the high temp wash and heated dry buttons were on. Every thing on the diagnostics checked ok. Fill drain wash heater all worked ok. The lights were on until I opened the door. Could not find any thing on diagram about the two lights. Any help would sure help.

What buttons do you have to push to get the dishwasher to go into diagnostics to reset control when the clean light is flashing 7 times and pauses and goes through that over and over. Have replaced the heater but some idiot took the diagnostic chart so I don’t know what the correct buttons are. Thanks for all your help.

Hello

We have an electrolux ewdw6505gs0 that we have had for about 6 years. Recently it stopped washing the upper rack as good as it used to. It’s not every time but appears to be more bad than good. I have removed all of the parts that the water passes through and have found no obstructions including the pump and hoses underneath. I am very handy and have an extensive set of tools so any repair or diagnostics necessary I should be ok to do. Dishwasher has never had problems until now. My hope is to fix it rather than have to shell out $800 for a new one. I suspect it could be a weak pump or a control board but I dont want to throw unnecessary parts at the problem you have a way I can diagnose what the issue is.

Thank you

hi , i am an appliance repair man in canada, and i have a customer that has an 3C error mid cycle, i went there ran the machine for 10 minute nothing came up, tried to manually drain the machine drains fine, cleaned the filter, but dont know where to look for this error, nothing seem to be wrong with the machine.. please help

I have no lights on display and no power to control board.

I ran the dishwasher to see what happens. It fills up, sits quietly then empties. I positioned the sprayer arm at 6:00 between filling and empty. It doesn’t move.

Hello, I just replaced the defective touch panel. I need to know how to clear the error code on this model. Maytag dishwasher MDB4949SDZ. Thank you, Shawn

The complaint is that the dishes are not drying. I have no tech sheet and am looking for a way to run a diagnostic test or jump through the sequence so I don’t have to sit and wait for the element to turn on. The element does have continuity and 12.2 ohms. Thanks, Andy

The unit runs fine till the end then it doesn’t drain and the two LEDs blink. If I unplug it eventually it will clear and repeat the same problem. Any Ideas?

Poor washability.

Will not drain water.

Not drying properly.

Unit will not start.