My Maytag dryer makes a clicking noise during the cycle and smells like smoke.
- Harley Clark asked 10 years ago
- last active 10 years ago
This dryer does not heat, plus in any cycle it will shut down after 2 minutes of running. The heater is bad, but not sure if the other problem is the most likely cause of the motor, or if it is the board. Any ideas?
- Guest asked 10 years ago
- last active 10 years ago
My Maytag dryer is making a loud noise when in use.
- Patrick's Appliance Service asked 10 years ago
- last active 10 years ago
Sometimes that message comes up and sometimes it finishes cycle no problem. What could be causing that? I did some research and found the control board to be the culprit. Board is no longer available. Is there a repair that can be made to the board? Like replacing capacitor, relay, etc.?
- mdhomeservices asked 10 years ago
- last active 10 years ago
What should I look for when the lint alarm goes off and kills the dryer? On a separate call, I replaced the belt, pulley, rollers and blower wheel. I Vacuumed Out The unit and was working fine when I left. ????
- Guest asked 10 years ago
- last active 10 years ago
My Whirlpool dryer is displaying a 01 error code.
- Don Kopecky asked 10 years ago
- last active 10 years ago
My amana dryer is making a loud squeaking noise.
- Hall Refrigeration asked 10 years ago
- last active 10 years ago
My Whirlpool dryer will not start and only makes a clicking noise.
- T&G Appliance Repair asked 10 years ago
- last active 10 years ago
My Whirlpool dry only heats sometimes.
- Patrick's Appliance Service asked 10 years ago
- last active 10 years ago
My Frigidaire dryer is not drying clothes properly.
- David Sutton asked 10 years ago
- last active 10 years ago
My Whirlpool dryer is making loud horrible noises
- Gary Williams asked 10 years ago
- last active 10 years ago
Hi Folks,
This dryer was in a very poor condition. The pulley had fallen off the fan and the owner kept using it with no circulation of heat. No fuses were found to be defective. Element checks out! Proceeded to clean the unit thoroughly. Took care of the pulley and circulation problems. Put it all back together and no heat. Check the board and it was fried. Installed a new board and still no heat. There was no tech sheet with the unit! Now I have 240v going to the board (two legs of 120v each) but where do I find the legs coming out. It’s the heating cycle because the dryer is turning but no heat. I need a tech sheet and some expertise on getting this unit on board!
Thank you,
Jan
Barney’s Appliance
- Guest asked 10 years ago
- last active 10 years ago
Can you give me some help, I would appreciate it.
First let me tell you, my dryer is completely apart! When the dryer was put on “Time Dry” it did not dry the clothes. It at first got slightly warm. And then went thru the whole time without drying the clothes.
What would you consider the most likely part(s) to be ? And how would I go about testing the component(s) with VOM?
Thanks for your help and time, Rich.
- Guest asked 10 years ago
- last active 10 years ago
My Frigidaire dryer will not start.
- Patrick's Appliance Service asked 10 years ago
- last active 10 years ago
My Maytag dryer is not tumbling and the sensing light is on
- Curtis Appliance Repair asked 10 years ago
- last active 10 years ago
My Frigidaire dryer is squeaking and giving off a burning smell
- T&G Appliance Repair asked 10 years ago
- last active 10 years ago
My RCA dryer is making a loud squeaking noise
- Don Kopecky asked 10 years ago
- last active 10 years ago
My Maytag dryer is not advancing and is not heating properly.
- Hall Refrigeration asked 10 years ago
- last active 10 years ago
My Whirlpool dryer wont start and is just making a buzzing noise
- Fred Abernethy asked 10 years ago
- last active 10 years ago
My Frigidaire dryer is making a loud squealing noise.
- Patrick's Appliance Service asked 10 years ago
- last active 10 years ago
Push button for start broken out. Go to replace console and find once I remove the 2 circuit boards from the console that the start pad on user interface board is busted. Great, more issues. LOL
Trying to price out part, I run into a headache. Original part number is W10110658.
1. First parts house tells me special order. They check Whirlpool inventory and says they have 10 in stock. But customer doesn’t want to wait.
2. Second parts house says part number changes to W10294715. In stock. Something don’t seem right. Call 2 more parts houses.
3. Third parts house says part number now W10756696. Not in stock.
4. Fourth part house says part number is W10294708. In stock.
- Hall Refrigeration asked 10 years ago
- last active 10 years ago
Hi folks,
This unit is only about three years old and in a RV. I knew I should have walked but they sounded like nice people and they are a couple of snow birds from Michigan! Nice folks.
Compliant: Press the start button..nothing. checked all the oblivious things but I cannot get voltage to the timer or start button. Checked the fuses, voltages coming in! Small area to work in. Any ideas??
All ideas greatly appreciate!
Thank you,
Jan
Barney’s Appliance
Palm Bay, FL
- Guest asked 10 years ago
- last active 10 years ago