Appliance Type: Refrigerator

My Frigidaire refrigerator is not getting water to the ice maker.

My Whirlpool refrigerator is dripping inside.

My ice maker in my Whirlpool refrigerator is making too much ice.

My Frigidaire refrigerator is flashing “4” and beeping.

GOOD MORNING. I DID NOT CHECK THIS FRIDGE YET. I AM BEING TOLD THAT THE FRIDGE TEMP IS FINE, BUT THE FREEZER IS NOT. ALSO, THE ITEMS IN THE FRIDGE VEGIE STORAGE DRAW ARE FREEZING. I NEVER WORKED ON A HOTPOINT BEFORE, BUT THIS SOUNDS BACKWORDS. ANY HELP WOULD BE GREATLY APPRECIATED. THANKS, TODD FROM NY.

My Whirlpool refrigerator is not dispensing ice.

My GE refrigerator is not cooling all frosted up and I checked the timer and thermostat they are good.

My Whirlpool refrigerator is leaking water.

My GE refrigerator is not cooling.

The icemaker in my Kitchenaid refrigerator is not working.

These videos of subzero 511 doesn’t show.

https://www.appliancevideo.com/?cat=&find=511&post_type%5B%5D=post&post_type%5B%5D=premiumvideos&post_type%5B%5D=fromthefield&post_type%5B%5D=embdvideo

Your 511 videos are showing up.

I replaced the water inlet valve and the dual inlet valves due to the failed continuity readings (I actually measured the wrong switch, so I have an extra valve now grrr).
I waited over a week and still no ice. I also felt no water in the tray, so I thought the ice maker water line was clogged. Checked that by blowing air through it and it was clear (still no ice).
Put the fridge in diagnostics and ran the ice maker through a cycle and it ran fine up until it needed water. The service test 25 never showed a Digit 1 other than 0. Tested voltage to the solenoid and nothing there. The door water valve gave 122v.

Now I am at a loss to determine if it is;
-the wiring harness
-the ice maker
-control board.

I thought it would be worth the $25 to ask you how to go about testing for which of the above it could be.

Thanks for your help,

Tom

So from what I gather this unit was damaged by a storm power surge. When you open the door there are no lights, light bulbs are ok. The ice in the door bin will not dispense and ta majority of the time it doesn’t make ice. I am also concerned that when the fridge door switches are held that I do not hear either the evap fan or the icemaker fan. Please advise.

I’m repairing a ge monogram 10 yrs of age, I found a capacitor to be bad, this capacitor is located in the back of the unit at the top where the compressor compartment is located. I Haven’t been able to lpocate this capacitor on any site the only capacitor I can locate is the one located in the front of the compressor compartment that is a small black rectangle which is still good and I don’t require. The capacitor I’m searching for is silver 4 to 6 inches in lenth has 3 prongs and is a cylinder in shape. Would you know where I could find this part

I can’t see any way to get to change the auger motor on this unit. There isn’t a opening on the bottom as the older styles had. Any ideas or videos you have would be wonderful.

The right door on this refrigerator pops open when the left door is closed first. I replaced the door cam, part #12028505ap but it did not stop this from happening. I have been telling my customers to open both doors and close the left door first in order to insure both are doors are sealed properly. I have not found an answer on the web. Hopefully your repairmen have found a solution.

Thank you!
Mel
My Appliance Repairman Inc.

The compressor its not working so i check power at the terminals and it has like 28 vac, i replace the 2 control boards on the back and still dont work, where else can i check, i also check the capacitor and its good and it doent have a start relay, it look like it start with one of the control boards

Samsung freezer is over freezing and making frost on inside of whole freezer. I/M does not work, and it actually looks like the freezer door is not being shut all the way, but they swear it is pushed shut every time. Any ideas? I know this particular I/M has a sensor on it, could this be the issue as well?

My Whirlpool refrigerator is leaking water on the floor and it seems to be coming from the back of the unit.

My GE refrigerator is not cooling properly. It has a lot of frost on the back panel.

I replaced the ice maker in this Amana refrigerator. Since replacing, cubes are not hardening, ice is clumping in the bin because water not completely frozen when harvested. Temp in freezer is zero. The Amana ice maker part number changed to the DQ model. I transfered over all the parts to the new model. I’m thinking the harvesting is happening to soon or the heater is on to long. The ice maker did not harvest any ice in the first 24 hours and the cubes were frozen toward the evaporator but not completely frozen to the front of the unit. Any ideas on whether I should try a second ice maker or what to look for? Thanks for your help in advance

Main control board relay\resistor popped replaced that board fridge compressor came on but not cooling fan in freezer not running

Samsung rs263tdbp keeps icing up. Replaced thermistor and evaporator fan previously but customer calls back after 6 months to a year when it frost up again.

The above fridge is a french door type with the TV monitor, Pandora. Problem is the drawer above the freezer has no lights shining that would turn on when the freezer were to be opened and the touch panel on this deli drawer is unresponsive. Everything else is working in the fridge.All other lights and it is cooling. Best Buy told the customer that the rear main control board would need to be replaced. Thank you for any advise.

We have a Maytag refrigerator that was not cooling in the fresh food compartment. We have no technician diagnostic sheet with this unit. We replaced the thermistor the air damper is now open but it is freezing the fresh food compartment. The freezer is fine. We checked the unit found damper closed.
The customer called back 2 days later and the fresh food is now freezing everything.
There are no problems with the defrost system.
The evaporator fan motor is fine.

Thanks in advance.

Not sure if you will see this, but I have a question. I replaced the heater and the sensor and It looks like I received the same replacement heater you all used. Where the wire from the left side has its own connector. The OEM heater’s left side wire is connected with the right to go into the same wire harness. In your video at the 8 minute mark you all cut and go to the finishing steps. Before that, the left wire is still sitting unconnected. After 8 minutes it is connected. Did you all splice the wire? in the empty harrness/connector that was on the right wire or do you leave it dangling and do nothing? This is the second time I have ordered this part. It does not look exactly like the original but close. Help I am at a total loss here. I have pics if I can send them.