Have E 22 fault code which I know is the fresh food fan. Problem is code will not reset and nothing else will start up on the unit. Can here the control board click but compressor never cuts on. Any ideas?
- Guest asked 9 years ago
- last active 9 years ago
Hi, I have just purchased a secong hand fridge Samsung top fridge bottom freezer. The display says its 15c in fridge and -21 in freezer. The actual temp is 10c in fridge and 1c in freezer, the fridge light is not consistent so I removed the bulb and the unit beeps 11 times every 2 minutes.
- Brent asked 9 years ago
- last active 8 years ago
I need error codes on this Samsung refrigerator model & troubleshooting guides ….thank you
- Dalas G asked 9 years ago
- last active 8 years ago
Have LG refrigerator with ER 1F code. Fan motor for icemaker runs then shuts off.
Has anyone ran into this problem?
- RANDOLF APPLIANCE SERVICE asked 9 years ago
- last active 8 years ago
ERROR 14E. Both freezers on the bottom cooling, ice cubes frozen. Fresh food section on top warm costumer said it was cooling when they unplugged and re-plugged but now error code is back and not cooling. Freezer -2, fridge 34f but actually about 57f.
- Guest asked 7 years ago
- last active 7 years ago
Frigidaire refrigerator fphg2399pf1 is dead. No lights . . . not working. Tested outlet. Have electrical diagram. Mother board has power. Ordered new motherboard. Did not fix.
- Guest asked 8 years ago
- last active 8 years ago
The fridge temp is to high. I found on the lower left side of the fridge a small block of ice, where the vent should be. I thawed out the ice turned the fridge back on, and felt no air flow ( either wat ).
The top left side vent was blowing cool air. Not a lot of air flow, but I could feel air moving.
- Guest asked 6 years ago
- last active 6 years ago
Hello,
We went out to service a samsung fridge that the bottom freezer door won’t open. We thought the railing might be frosted over and unpluged the fridge in order for it to defrost, it has been two days since and it still wont open. Any suggestions?
- mytechjoe asked 8 years ago
- last active 8 years ago
I have been wrestling with this for the past two days – ever since my wife noticed that everything in the fridge was frozen. This is a Samsung unit with the fridge on top and the freezer on the bottom. The freezer is working just fine and the freezer display agrees with a separate freezer thermometer I put inside the freezer. The fridge side, however, is set at 38*, but the internal thermometer says it’s about 12* in there!
I downloaded the service manual for this model fridge, but it is rather poorly written. I checked for trouble codes, but I didn’t have anything that matched what was in the service manual. On start up my display will completely light up for a second or two, then go dark and then a number “3” will pop up of the refrigerator side of the display. Then the display will show the actual temperatures of the freezer and fridge before going back to displaying the selected temperature settings.
A quick online search indicates a bad thermistor in the refrigerator section. I am a little wary because on start up, the fridge displays actual temperature quite accurately. Some thermometer inside the fridge is working. I get that a thermistor is not a thermometer and that if the thermistor is responsible for making the fridge self-defrost, then I guess it would make sense.
I suspect that the fridge evaporator is completely iced over. In an effort to remedy this, I went into the “forced operation” mode and selected fridge defrost. I’m currently listening to my bridge beep constantly as I wait to see if this does anything.
Food safety is something that I really obsess about and getting this fridge back to normal as quickly as possible is a huge priority for me.
Any help you can offer is greatly appreciated!
Ed
- Ed asked 10 years ago
- last active 10 years ago
refrigerator is not cooling at all but the compressor is running
- Guest asked 8 years ago
- last active 8 years ago
Top freezer working fine. Bottom fridge is too warm. Watched your video, took apart top panel, evaporator fan motor not working. dial switch in fridge makes no difference. I tested wires to evaporator motor fan, not getting any voltage to fan motor? The fridge has the dial switch that says “coldest to lowest”. took that panel down, it has the thermostat dial switch, and there is a white square thing with wiring harness connected to it next to the dial switch.
What would be stopping power from reaching the evaporator fan motor? FYI, this all happened after a power pole was hit in neighborhood, causing outage/spike. The condensor and it’s fan is running fine, freezer is working fine. Just not the fridge.
- Guest asked 8 years ago
- last active 8 years ago
It won’t clear by un plugging it . I can’t program it into a service mode. What does the code mean and what can I do?
- Guest asked 5 years ago
- last active 5 years ago
The refrigerator was not running. I look at the main board and observed the green light on the board blinking 6 times continuously after 3 seconds it blinks 6 times continuously. is it an error code or what. The tech sheet said nothing about the blinking light on the main board.
- Guest asked 7 years ago
- last active 7 years ago
Both the fridge and the freezer are not operating at their proper temperature. They are both cool, but the fridge is not cold, and the freezer is not freezing.
- Guest asked 8 years ago
- last active 8 years ago
Frig and freezer run hot compressor runs condenser fan runs don’t know about evaporator fan when door is open can hear it when door is closed can’t hear it. Is there a way to check to see if its running? Doors don’t have switches (push in ) its a magnet at bottom of freezer door.
- dan0418 asked 9 years ago
- last active 6 years ago
My question has nothing to do with the specific model number of above. A coworker and I changed out a bad compressor. It ran for 2 days, then stopped. We were discussing our problem with other techs. One of the other tech asked us how we filled the new compressor with freon. We told him that we filled it with liquid on the low side line like we always do.
He said that we improperly filled the compressor and thus, broke it. He told us that the only way to properly fill a compressor is liquid on the high side and vapor on the low side. Now, we have made over 25 compressor change outs, and never had a problem.
What is the “only” or is there an “only way to fill a compressor?
- Guest asked 8 years ago
- last active 8 years ago
This is the first time we are seeing this refrigerator. It has a feature known as “AutoFill”. You place a cup or container on the water/ice dispenser platform and the fridge automatically fills the container to the appropriate level. This particular fridge keeps displaying “No container” when you place a cup and hit autofill. I tried researching this and found that it is sometimes the result of a non-uniform container. Our technicians tried several container types that were uniform and still received the same error message. All other functions of the refrigerator are working fine.
- Guest asked 7 years ago
- last active 7 years ago
I am working on a 4 door kitchenaid refrigerator that has icemaker in the celling in refrigerator side how do you get it out , dose anybody have a service manual to share whit me MOD#KFIS29PBMS02 and SER#K33307442 help is very appreciated
- Hall Refrigeration asked 9 years ago
- last active 9 years ago
So I have a Frigidaire refrigerator from 2009 that seems to no longer hold a steady temp in the fridge section and even when I turn the thermostat to make it colder it will turn on for about one minute and then shut off and then 3 minutes later do the same thing over and over again. There is no ice build up in the freezer and that is holding a steady temp of around 20 degrees but will not get colder than that. The fridge side will not get colder than 40 degrees and will flutcate between 40 and 45 depending on how much we open the door. Even the coldest setting on the thermostat there in no change in the fridge temp or freezer temp as well.
- John Christiansen asked 9 years ago
- last active 9 years ago
I have a Samsung refrigerator. This is a French door unit.
The back panel in the fresh food compartment was solid ice the evaporator fan blade was frozen half way up.
I pulled the plug defrosted the back took it out. Replaced the evaporator fan. Plugged it back in the display, located inside at top showed 88 on the freezer side of control and the fresh food side of control. The evaporator fan was not running. I did have both doors open about 3 hours and ran a steamer inside to defrost the back panel.
The settings will not respond at all and the fan is not running. Is there something I need to reset? Thanks In advance
- Fred Abernethy asked 9 years ago
- last active 9 years ago
This freezer section thawed , then rebooted and cleared has worked ok then showed h1. then before it defrosted started working again.
- Guest asked 7 years ago
- last active 7 years ago
Customer ice dispenser makes a grinding noise when depressed. The ice dispenser works well without the noise.
- Guest asked 8 years ago
- last active 8 years ago
Need to replace the touch pad control for the water/ice dispenser. If anyone has a diagnostic manual that you would be willing to send me, I would appreciate it. Thank you.
- Fred Abernethy asked 9 years ago
- last active 9 years ago
I cannot get the ice maker to function into harvest cycle. I need help with diagnostics.
- T&G Appliance Repair asked 8 years ago
- last active 8 years ago
How do you reset the control panel on a Maytag refrigerator, model #MFI2569YEM0 display board lights up when you touch any button beeps when you push water or ice button but no lights unless you push a button
- Fred Abernethy asked 5 years ago
- last active 5 years ago
I have a Kenmore refrigerator model number 797.77563600 on a plane video it comes up with no match I am having an error code on this refrigerator ER FF
- Guest asked 9 years ago
- last active 9 years ago
Refrigerator giving me a C4 error code.
- Patrick's Appliance Service asked 4 years ago
- last active 4 years ago
I’ve watched your videos on how ice build up behind the back panel will prevent a frig from getting cold. I’ve also had to remove this build up of ice myself a total of 3 times. I noticed after the last time I removed the ice and plugged it back in my frig temp gauge would show 34 degrees but the compartment was not close to being that cold. Why would my frig not get as cold as the temp gauge even after I cleared all the ice out? Now I’m in the process of removing ice again and my question is what part do you think, based on your experience as a repair technician, I need to replace so I don’t have to do this every 2 months? I can verify that the fan is still operating properly. Would you suggest I replace the heater? Or the sensor? If I purchased the heater would the sensor also come with it? The frig is only 2 yrs 4 months old. Thanks for your help.
Art
- Art asked 10 years ago
- last active 8 years ago
Model number LFX25991ST/06 What position is the refrigerant valve in when the refrigerator is unplugged? I want to pull a vacuum and I know the Whirlpool you have to use diagnostic mode to open the 3-way valve. Is that the case with
the LG?
- Tim O. asked 9 years ago
- last active 9 years ago
the 1st steps just yield c– – f on the freezer display and 0c on refrig display when I do steps 1,2,3. it reverts back to set freezer temp and refrig temp after a few minutes. what am I doing wrong?
- r0n asked 10 years ago
- last active 10 years ago
