Appliance Type: Washer

The code is telling me the the cold side of the water inlet valve is letting it spin.

Can you send me a video on how to replace a spider bracket for a front load wahser?

Machine does not complete cycle – no spin

Problem when spinning make a lot noise whirlpool washer

Please me help

Customer complaint before arrival is washer will not spin the clothes out at the end of the cycle. Homeowner did advise that it will only work on bulky cycle technician arrived. Had an F5 E2 code door lock assembly error. We replace that unit is still not spinning out on any other cycle, except for bulky, when we came back out, we went to retrieve the error codes and there was none in there ran a cycle on normal and it does not spin out the clothes. You can turn it to drain and spin and it will spin out the clothes properly also, the drain is working properly too , not quite sure where to go with this any help would be appreciated Please email me if you need more information or need anything. Thank you, Daniel Woods.

washer is not draining, but I just replaced the pump 2 yrs ago, the pump seems to have proper resistance, touching it through the filter hole.
I recall the flapper can be a problem , it’s a rubber check valve . Is it possible a hot steam cycle made is flexible enough to push through and cause problems with all cycles? it started on steam cycle, now all cycles won’t drain. I thought i would ask you guys before I go to the trouble on this .

also I know your 29.00 only co=vers one appliance , but I just need a recommendation, matching dryer dv448gp/xaa is a bit noisy, do you guys recommend replacing the springs and wheels around the drum, or should I wait till some happens?

Not spining

Washer give a cancel error on heavy bedding loads. What could be the cause of this?

We have replaced the main control board on this unit. The code “UR” is popping up no matter the size of the load. Small or Large.

What are the reasons the capacitor keeps blowing? And how do you test them? The motor runs, the agitator moves freely and so does the drum. The drain pump is clear.

Hello,
My load began washing, and during the wash cycle, maybe 5 minutes in, the E3 Code went off. Now my washer is full of water, and I can’t get it to go past this error code.
Is there a way to make it drain without the lid closed? My washer is full of water and won’t do anything because it thinks the lid is open.
I watched your video on how to change the switch, but I don’t want to let water sit in my washer for a week until the part comes in.
Is there a way to override the system so I can at least drain the water?

Thank you,
Rachel

Main control board and inverter board have been replaced Polarity at plugged checked good put washer on normal cycle drain pump kicks on while sensing door does not lock and does not fill with water door lock flashes on display E91 error code

GE Washer fills with water and starts to turn for about 5 seconds and then stops.

Hello, I have a Speed Queen washing and drying unit that I want to maintain and I would like you to send me the maintenance and repair manuals for the washing machine Model: AFN50FSP111TW01 Serial: 1201004722

I also want to tell you that in the previous question, I was wrong, the model and serial number of the dryer, the correct one is the one that comes in the text box, I hope you can help me with this, I already have the newer dryer and it is one with which I also count, since you gave me an answer in previous dates.

The dispenser pump motor runs but it’s not measuring and adding the soap.
The blue soap dispenser is in it’s proper place. How do I check if the dispenser pump is pumping?
I’m referring to the w10842325 dispenser and pump assembly.
Could the hoses be clogged?
Please explain In as much detail as you can.
I notice when i run the diagnostics that though that small pump motor runs it doesn’t turn on the water valve. I suppose that the water it pumps into the dispenser comes through the mixing valve.

Could a faulty UI cause the main control board to short circuit and fry?

My technician replaced a faulty control board and pressed the start button to go into service mode – the board was immediately fried, only after pressing the start function.

I’m reaching out on this one because I’ve already lost two control boards for this repair. 🙁

Hello, I have a Speed Queen AFNE9BSP113TW01 washing machine, which is presenting me with the P5 error code, this appears after having changed the Mixing Valve. Could you tell me if this is connected and what do you recommend I do?

I followed the instructions in the Video on your page for the Speed Queen AFNE9BSP116TW13 washing machine, because I did not find the specific video for my washing machine.

My washer is hard to start. I put it in diagnostic mode and get codes F0 E3

I have ohmd out the unbalanced switch which tested good. I can hear the lid switch when the washer tries to go in to spin mode. About 15 seconds later it displays the Er UB error. The machine is level with no broken springs. Wires to the swich look fine.

my electrolux washer will not start the cycle.

My washer is not cleaning my clothes properly.

Hello I have a question on a Electrolux Washer. I’m noticing these issues: Will not run

My Electrolux washer seems to be off balance.

Clothing gets stuck, tub moves around a lot, bad smell, standing water.

DDO Error, Fabric Softener will not dispense, drawer will not drain, Clothes are not getting clean.

E91 Error, display goes blank, will not run.

Screen is blank, E90 Error, ERR is on display, runs then shuts off, random numbers and letters on the display.

Over fills with water, Starts to fill and stops, E32 Error.